background image

8

9

5. While holding the search coil about 1-2 inches above the ground, slowly move the 

    search coil over the area where you placed the sample, sweeping the search coil 

    in a side-to-side motion.

   Note: Before trying to find other metal in the area,  press the RED button to return 

   the meter pointer to “0”.

Search Coil Sweeping Hints

1. Never sweep the search coil as if it were 

    a pendulum. Raising the search coil 

    while sweeping or at the end of a sweep 

    causes false readings.

2. Sweep slowly – hurrying makes you 

    miss targets.

- If the detector detects the material, sound 

  changes and the pointer moves to different 

  directions according to the types of metal 

  it finds.

- If the detector does not detect the material, 

  make sure you are moving the search

  coil correctly.

  Notes:

  The detector responds with a strong signal when it detects most valuable metal 

  objects. If a signal does not repeat after you sweep the search coil cover the target 

  a few times, the target is probably junk metal.

   False signals can be caused by trashy ground, electrical interference, or large 

   irregular pieces of junk metal. False signals are usually broken or unrepeatable.

Useful Skills

How To Use DISC

Discrimination is the detector’s ability to differentiate between types of metal. The 

detector’s DISC setting determines whether the detector will distinguish between 

different types of ferrous and non-ferrous metals.

You can set DISC to minimum (fully counterclockwise), then rotate clockwise, the 

detector first discriminates iron, then pull tabs and nickel. When you set the DISC 

fully clockwise, silver still can not be discriminated. The sound will be lower or even 

disappear and the pointer will move to left when the unit detects discriminated metal. 

The sound will be higher and the pointer will move to right when the unit detects 

metal which is not discriminated. 

Wrong

Correct

Note: Each time you use the detector in a different area, you must adjust the DISC. 

Each search location presents new challenges.

About False Signals

Because your detector is extremely sensitive, trash-induced signals and other 

sources of interference might cause signals that seem confusing. The key to 

handling these types of signals is to dig for only those targets that generate a strong, 

repeatable signal. As you sweep the search coil back and forth over the ground, 

learn to recognize the difference between signals that occur at random and signals 

that are stable and repeatable.

Factors That May Affect Detection

No detector is 100 percent accurate. Various conditions influence metal detection. 

The detector’s reaction depends on a number of things: the angle at which the object 

rests in the ground, the depth of the object ,the amount of iron in the object, the size 

of the object.

Pinpointing A Target

Accurately pinpointing a target makes digging it up 

easier. However, you need practice to improve this 

skill, therefore,  we suggest you practice finding and 

digging up small metal objects on your own property 

before you search other locations. Sometimes 

targets are difficult to accurately locate due to the 

sweep direction. Try changing your sweep direction 

to pinpoint a target. Please follow these steps to 

pinpoint a target

1. When the detector detects a buried target, continue sweeping the search coil over 

    the target in a narrowing side-to-side motion. Make a visual note of the exact spot 

    on the ground where the detector beeps.

2. Stop the search coil directly over this spot on the ground. Then move the search 

    coil straight forward away from you and straight back toward you a couple of 

    times. Make a visual note of the exact spot on the ground where the

    detector beeps.

3. Repeat Steps 1-2 at a right angle to the original search line, making an “X” pattern. 

    The target should be directly below the “X” at the point of the loudest response.

Содержание WINBEST D-50 Edition







Отзывы: