Barry-Wehmiller Accraply 204RH Скачать руководство пользователя страница 42

Страница: 42 / 97

SECTION 1: SYSTEM OPERATION

MAINTENANCE

PROBLEM

PROBABLE CAUSE

SOLUTION

Motor sounds

“rough” or

vibrates.

Overloaded motor caused

by restriction of labels and/or

backing paper as it passes

through the machine.

Check all solutions listed under Items

2 and 5 above.

Defective motor.

Replace motor.

Labels feed

continuously.

Translucent labels (cannot

be “seen” by label sensor).

Check label opacity and notify

Accraply (see Customer Service on

page i).

Label sensor out of

adjustment.

Adjust label sensor light and/or

sensitivity.

Label roll

rotates without

stopping.

Unwind not adjusted

properly.

Adjust unwind to provide more brake.

Label web

sags between

dispense

tip and

rewind after

dispensing a

label.

Rewind not adjusted

properly.

Adjust rewind to provide more

clutches.

10 Malfunction of

valve solenoid.

Machine not plugged in.

Plug in power connector.

A fuse is blown.

Change the fuse.

Open wiring.

Check for proper connection.

11 Improper

equipment

operation.

Air leakage.

Replace parts as necessary

(gaskets, seals, and hoses). (See

Recommended Spare Parts List on

page ii)

Malfunction of filter

element.

Clean or replace the filter element.

Condensation accumulation

in air filter.

Remove condensation from air filter.

12 Labels double

feed.

Missing labels on roll.

Inspect roll and contact Accraply if

necessary (see Customer Service on

page i).

Label sensor out of

adjustment.

Adjust label sensor light.

Содержание Accraply 204RH


































































































Результаты поиска

Содержание Accraply 204RH

Отзывы:

Похожие инструкции для Accraply 204RH

Бренды по названию

Популярные бренды

Barry-Wehmiller Accraply 204RH, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Accraply 204RH

Отзывы:

Похожие инструкции для Accraply 204RH

Бренды по названию

Популярные бренды