Barry-Wehmiller Accraply 204RH Скачать руководство пользователя страница 38

Страница: 38 / 97

SECTION 1: SYSTEM OPERATION

OPERATING PROCEDURES

Clearance Pause

The clearance sensor has

detected the next product

before the wipe-down

sequence has completed. (See

3.5.4 Clearance Sensor)

Conveyor and spacing wheels

pause. Green light on light

stack flashes during pause.

Wipe-down sequence finishes.

After wipe-down sequence is

completed, the conveyor and

spacing wheels resume and

system continues. Solid green

light on light stack when system

resumes.

Manually feed two products

onto the conveyor after the

spacing wheel closely together.

Alternatively, trigger the

clearance sensor with your

hand in the middle of a wipe

cycle.

VFD Fault

The conveyor drive has faulted. Machine stops. Solid red light

on light stack. Flashing red

HEAD/DRIVE indicator light on

control panel. Alarm must be

cleared by pressing the Alarm

Reset button before restarting.

Shut down and lock out power

to the system. Remove the

fuse for the VFD. Recover

power to the system and

attempt to run.

204 Not Ready

Output from head. Possible

head errors are listed in the

204/206 Service Manual under

“Error Messages”.

Machine stops. Solid red light

on light stack. Flashing red

HEAD/DRIVE indicator light on

control panel. Alarm must be

cleared by pressing the Alarm

Reset button before restarting.

Rotate the rewind dancer arm

clockwise to its end position

and hold until the error occurs.

Safety Circuit (E/

Stop or Interlock)

An E/Stop has been pressed or

the Interlock has been opened.

Machine stops. Power is cut

to conveyor and spacing wheel

drives. Air is dumped. Solid

red light on light stack. Solid

red HEAD/DRIVE indicator light

on control panel. E/stop must

be released, or interlocked door

closed. Alarm must be cleared

by pressing the Safety Reset

button and the Alarm Reset

button before restarting.

Press an E/Stop button or

open the wipe-down station

enclosure.

Содержание Accraply 204RH


































































































Результаты поиска

Содержание Accraply 204RH

Отзывы:

Похожие инструкции для Accraply 204RH

Бренды по названию

Популярные бренды

Barry-Wehmiller Accraply 204RH, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Accraply 204RH

Отзывы:

Похожие инструкции для Accraply 204RH

Бренды по названию

Популярные бренды