Barrett BH8 Series Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 84

background image

BH8-Series – User’s Manual

[email protected]

www.barrett.com

© 2007 Barrett Technology®, Inc.

Document: D3000, Version: AF.00

Page 41 of 82

6.4 Example

This application uses fingers 1 and 2, and the spread. The fingers will receive velocity control
information and report strain and delta position. The spread will just report delta position. The
feedback block will also include the present hand temperature. All relevant coefficients will be set
to 1.

To set this, use the following commands:

12FSET LCV 1 LCVC 1 LCPG 0 LFV 0 LFS 1 LFAP 0 LFDP 1 LFDPC 1

4FSET LCV 0 LCPG 0 LFV 0 LFS 0 LFAP 0 LFDP 1 LFDPC 1

PSET LFT 1

124LOOP

The hand will then send a single "*" and wait for control blocks. Each control block will consist of
three bytes:

"C" [Control data follows; respond with feedback block]

1 signed byte of velocity for motor 1

1 signed byte of velocity for motor 2

Each feedback block will consist of eight bytes:

"*"

1 unsigned byte of strain for motor 1

1 signed byte of delta position for motor 1

1 unsigned byte of strain for motor 2

1 signed byte of delta position for motor 2

1 signed byte of delta position for motor 4

2-signed bytes of temperature

Each control block from the host will stimulate a feedback block from the hand. When the host is
finished, it will send the single character ^C (0x03); the hand will respond by printing a prompt
and waiting for a new command.

7 Maintenance

7.1 Finger Cable Pretension

The third joint in each finger is driven by a brushless servomotor through opposing stainless steel
cables that act like tendons transmitting torque from a pulley at the base of the finger out to a
pulley at the fingertip joint. If you have purchased the joint-torque sensor option, the difference in
tension between the tendon pair is used to determine the torque at the third joint. The fact that we

«
...
41
42
43
44
45
...
»

Содержание BH8 Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для BH8 Series

Бренд: EFORT Страницы: 55

Бренд: EFORT Страницы: 305

TI Robotics System Learning Kit

Бренд: Texas Instruments Страницы: 25

Бренд: STEMCenter USA Страницы: 110

Бренд: Epson Страницы: 208

Бренд: Epson Страницы: 168

Бренд: Epson Страницы: 236

Бренд: Epson Страницы: 346

Flamewheel Robot

Бренд: DFRobot Страницы: 2

40 CPR Quadrature Encoder

Бренд: Phidgets Страницы: 3

Бренд: SPAWN Страницы: 9

Бренд: PI Страницы: 59

Бренд: MD SPORTS Страницы: 17

MOSS Exofabulatronixx 5200

Бренд: Modular Robotics Страницы: 36

Sabertooth 2X25

Бренд: Dimension Engineering Страницы: 2

InO-Bot Blockly

Бренд: TTS Страницы: 17

MOTOMAN-MH215 II

Бренд: YASKAWA Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды