Baroness LM285 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 65

Baroness LM285 Скачать руководство пользователя страница 21

Inspection Before Use............................Page 4-2

Reel Cutter (Cutting Cylinder) and
Bed Knife (Bottom Blade)....................... Page 4-2
Radiator Cover........................................Page 4-2
Radiator.................................................. Page 4-2
Coolant................................................... Page 4-3
Oil cooler.................................................Page 4-4
Hydraulic Oil........................................... Page 4-5
Air cleaner...............................................Page 4-6
Battery.................................................... Page 4-7
Tire..........................................................Page 4-8
Brake...................................................... Page 4-8
Belt..........................................................Page 4-9
Engine.....................................................Page 4-9
Engine Oil............................................... Page 4-9
Fuel.......................................................Page 4-11
Oil Leakage.......................................... Page 4-11

Tightening torques............................... Page 4-12

Standard tightening torques................. Page 4-12
Principal tightening torques ................. Page 4-13

Adjustment Before Operating..............Page 4-14

Adjustment of Seat............................... Page 4-14
Adjustment of Blade Engagement........ Page 4-14
Adjustment of Cutting Height................ Page 4-15
Adjustment of Cutter Adjustment
Spring................................................... Page 4-16

Procedure to Start / Stop Engine........ Page 4-17

Start / Stop of Engine........................... Page 4-17
Safety Mechanisms.............................. Page 4-18
Warning Mechanisms........................... Page 4-18

Operation of Each Section...................Page 4-18

Precautions for Operating the
Machine................................................ Page 4-18
Cautions for when You Leave the
Machine................................................ Page 4-18
Instruction Decals................................. Page 4-19
Light Switch.......................................... Page 4-20
Throttle Lever........................................Page 4-20
Reel Up/Down Lever............................ Page 4-20

Stop Valve............................................ Page 4-21
Mower Lock Lever (Latch).................... Page 4-21
Reel Rotation Lever.............................. Page 4-22
Anti-reverse Reel Rotation Stopper......Page 4-22
Reel Rotation/Stop Switching Lever..... Page 4-22
Traveling Pedal.....................................Page 4-23
Brake Pedal.......................................... Page 4-23
Parking Brake Lever............................. Page 4-23
Hood..................................................... Page 4-23
Underseat Cover...................................Page 4-24

Instruments........................................... Page 4-24

Instruments on the Operation Panel.....Page 4-24
Tachometer/Hour Meter........................Page 4-25
Water Temperature Gauge...................Page 4-25
Fuel Gauge...........................................Page 4-25
Pilot Lamps........................................... Page 4-26
Angle Meter.......................................... Page 4-26

Travel of Machine................................. Page 4-26

Moving the Machine............................. Page 4-26
Towing the Machine............................. Page 4-26

Cutting Work......................................... Page 4-28

Cutting Operation................................. Page 4-28

Transporting..........................................Page 4-28

Transporting Procedure........................ Page 4-28

Han

dlin

g Instru

cti

ons

LM285

Handling Instructions

Page 4-1

«
...
19
20
21
22
23
...
»

Содержание LM285


































































Отзывы:

Нет отзывов