Baroness LM285 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 65

Baroness LM285 Скачать руководство пользователя страница 45

1

Tachometer/Hour meter

2

Water temperature gauge

3

Fuel gauge

4

Pilot lamps (charge lamp, thermo-start
lamp, oil pressure lamp)

5

Angle meter

Tachometer/Hour Meter

The tachometer and hour meter are located in
the operation panel.
The tachometer indicates the engine rpm.
It is connected to a rotation sensor in the engine
flywheel area, and converts the signal output
from the rotation sensor into an rpm value.
The hour meter indicates total operation time of
the engine.
Every six minutes of engine operation will
increase the number at the first digit (black
number on a white background) by one. Every
one hour of engine operation will increase the
number at the next digit (white number on a
black background) by one.

2

1

1v6h5v-001

Tachometer/Hour Meter_001

1

Tachometer

2

Hour meter

Water Temperature Gauge

The water temperature gauge is located in the
operation panel.
This instrument indicates the water temperature
inside the engine.
If the water temperature gauge indicates a level
close to "H" during operation, the machine is
overheated.

Remove the load from the engine, idle the
machine for five minutes, stop the engine, and
then inspect the machine and perform any
necessary maintenance.
If the water temperature exceeds 105 degrees
Celsius, a buzzer will sound.

1

igozke-001

Water Temperature Gauge_001

1

Water temperature gauge

Fuel Gauge

The fuel gauge is located in the operation panel.
This instrument indicates the quantity of fuel
inside the fuel tank.

E

F

1

4

F U E L

1

2

3

4

1

2e4emp-001

Fuel Gauge_001

1

Fuel gauge

Han

dlin

g Instru

cti

ons

LM285

Handling Instructions

Page 4-25

Instruments

«
...
43
44
45
46
47
...
»

Содержание LM285


































































Отзывы:

Нет отзывов