Baroness LM285 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 65

Baroness LM285 Скачать руководство пользователя страница 43

1

Reel rotation/stop switching lever

A

Rotate

B

Stop

Traveling Pedal

Warning

This machine is not authorized as a special
motor vehicle. Do not drive it on public roads.

The traveling pedal is located in the right foot
area.
When depressed forward, the machine travels
forward. When depressed backward, the
machine travels in reverse.

1

yo3h9x-003

Traveling Pedal_001

1

Traveling pedal

Brake Pedal

The brake pedal is located in the left foot area.
To stop the machine, depress the brake pedal
all the way firmly.

1

ukjawr-001

Brake Pedal_001

1

Brake pedal

Parking Brake Lever

Caution

Be sure to release the parking brake before
driving.
It may result in the brakes or hydraulic
system malfunction.

Caution

Never park the machine on a slope.

The parking brake lever is located to the left of
the driver's seat.
To park the machine, depress the brake pedal,
and pull the parking brake lever completely.
To release the parking brake, press the push
button while lowering the parking brake lever all
the way to its resting position.

1

n9dmld-003

Parking Brake Lever_001

1

Parking brake lever

Hood

Caution

Do not open the hood in strong winds.

Caution

Be careful not to pinch your fingers when you
open or close the hood.

Unlock the rubber catch, then lift up the
hood.

1.

Han

dlin

g Instru

cti

ons

LM285

Handling Instructions

Page 4-23

Operation of Each Section

«
...
41
42
43
44
45
...
»

Содержание LM285


































































Отзывы:

Нет отзывов