Barnstead|Thermolyne NANOpure DIamond D11931 Скачать руководство пользователя | Manualshive

Страница: 17 / 56

background image

17

Cartridge packs will come bagged with four manifold
connection caps.

Part

Application

DIamond Kit Organic Free R/O & Distilled Feed
D50280 Ultra-Low Organics, Type 1 Water,

Reverse Osmosis or Distilled
Water Feed

DIamond Kit Organic Free Deionized Feed

D50281 Ultra-Low Organics, Type 1 Water,

Deionized Water Feed

DIamond Kit Type 1 R/O & Distilled Feed

D50282 Low Organics, Type 1 Water,

Reverse Osmosis or Distilled
Water Feed

DIamond Kit Type 1 Deionized Feed

D50283 Low Organics, Type 1 Water, DI

DI Water Feed

Each cartridge pack includes one 0.2 micron absolute
final filter.

Cartridge Pack Installation

1.

Open front (left side) door. Turn the cartridge
pack so the caps are facing you. Remove the
caps.

2.

Verify that each of the four posts on the car-
tridge pack has an o-ring.

3.

Lift unit manifold upwards, insert cartridge pack
and align the pack so that it mates with the unit
manifold.

4.

Lower unit manifold until it is flush with the top
of the cartridge pack.

5.

Hand tighten wing head screws securely.

6.

Close door.

Initial Operation

Note
Do not install the 0.2 micron filter and
bell assembly at this time.

Caution
Do not allow the NANOpure DIamond
Life Science (UV/UF) to operate
unless water is available to the unit.

Warning
Depressurize system prior to removing
cartridge pack.

Manifold

«
...
15
16
17
18
19
...
»

Содержание NANOpure DIamond D11931

























































Отзывы:

Нет отзывов

Похожие инструкции для NANOpure DIamond D11931

Бренд: GE Страницы: 28

Бренд: Zehnder Pumpen Страницы: 24

Бренд: Bartec Страницы: 46

Бренд: Farenheit Страницы: 39

Бренд: Farenheit Страницы: 31

Бренд: Farfisa Страницы: 72

KX-TDA600 - Hybrid IP PBX Control Unit Max. 1008...

Бренд: Panasonic Страницы: 66

Бренд: Park House Healthcare Страницы: 28

Бренд: F&U Страницы: 10

Бренд: ESAB Страницы: 143

Бренд: Telwin Страницы: 164

WELDER FANTASY BI-PULSE 201

Бренд: FACHOWIEC Страницы: 33

Бренд: Energie Страницы: 31

HYDRA-SPRAY President A Series

Бренд: Graco Страницы: 20

Бренд: iDataLink Страницы: 9

Бренд: Edwards Страницы: 46

Бренд: DTS Страницы: 72

Бренд: Schenker Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды