4
SECTION B: GENERAL INFORMATION
B-1) To the Purchaser:
Congratulations! You are the owner of one of the fi nest
pumps on the market today. CP&S pumps are products
engineered and manufactured of high quality compo-
nents. Over one hundred years of pump building experi-
ence along with a continuing quality assurance program
combine to produce a pump which will stand up to the
toughest applications.
This manual will provide helpful information concerning
installation, maintenance, and proper service guidelines.
B-2) Receiving:
Upon receiving the pump, it should be inspected for dam-
age or shortages. If damage has occurred, fi le a claim
immediately with the company that delivered the pump. If
the manual is removed from the packaging, do not lose or
misplace.
B-3) Storage:
Short Term-
CP&S Pumps are manufactured for effi cient
performance following short inoperative periods in stor-
age. For best results, pumps can be retained in storage,
as factory assembled, in a dry atmosphere with constant
temperatures for up to six (6) months.
Long Term-
Any length of time exceeding six (6) months,
but not more than twenty-four (24) months. The unit
should be stored in a temperature controlled area, a
roofed over walled enclosure that provides protection
from the elements (rain, snow, wind-blown dust, etc.), and
whose temperature can be maintained b40 deg.
F and +120 deg. F. (4.4 - 49°C).
Pump should be stored in its original shipping container.
On initial start up, rotate impeller by hand to assure seal
and impeller rotate freely. If it is required that the pump be
installed and tested before the long term storage begins,
such installation will be allowed provided:
1.) The pump is not installed under water for more than
one (1) month.
2.) Immediately upon satisfactory completion of the test,
the pump is removed, thoroughly dried, repacked in
the original shipping container, and placed in a
temperature controlled storage area.
B-4) Service Centers:
For the location of the nearest Barnes or Prosser Center,
check your Barnes or Prosser representative or
Crane Pumps & Systems, Inc., Service Department in
Piqua, Ohio, telephone (937) 778-8947 or Crane Pumps &
Systems Canada, in Brampton, Ontario, (905) 457-6223.
SECTION C: INSTALLATION
C-1) Location:
These pumps are recommended for general and light
construction, for sump and dewatering drainage, for dewa-
tering manholes and transformer vaults, for pit, tunnel and
trench dewatering, and for fl ood, fi re and other emergency
service cleanup.
Before pumping fl uids other than water, consult the
factory, giving fl uid, fl uid temperature, specifi c gravity,
viscosity, capacity in USGPM and total head and/or pres-
sure requirements, including friction loss through dis-
charge line, fi ttings, valves, etc. Pump may run dry for 5 to
10 minutes in air without damage where air can circulate
freely through the pump.
DO NOT
allow pump to be bur-
ied in mud or sand.
C-2) Discharge:
Discharge hose is recommended. If rigid pipe is used,
install so that there is no weight or strain on the pump.
C-3) Liquid Level Controls: (If Applicable)
Attach “ON” fl oat to discharge hose or pump cable at
desired pump “ON” level. Attach “OFF” fl oat to discharge
hose or pump cable at desired pump “OFF” level. The
“OFF” fl oat must be below the “ON” fl oat. To attach the
fl oats, thread the cable strap through the buckle with
the ratchet pawl, cinch up tight, thread excess strapping
through outer buckle slot. Be certain the level controls
cannot hang up or foul in its swing. It is recommended that
the pump is completely submerged when the level control
is in the “OFF” mode.
C-4.1) Electrical Connections:
The pump comes with a three wire cord and a three prong
grounded plug on the 120 volt models and a three wire cord
without a plug on the 240 volt models.
The 120 volt model’s cord assembly should not be
modifi ed in any way and must be connected into a three
wire grounded Ground Fault receptacle.
There are many different prong confi gurations for 240 volt
applications. An appropriate 240 volt plug to match your
receptacle will be required. Make sure the plug meets the
pump amp requirements found on the nameplate. Follow
the plug manufacturer’s wiring installation instructions.
DO NOT USE THE POWER CABLE TO LIFT PUMP.
C-4.2) Overload Protection:
An automatic thermal overload protects the motor. The
type of in-winding overload protector used is referred to
as an inherent overheating protector and operates on the
combined effect of temperature and current. This means
that the overload protector will trip out and shut the pump
off if the windings become too hot or the current passing
through them becomes too high.
Содержание 70 Series
Страница 8: ...8 Figure 2...
Страница 12: ...Notes...
