Barista Technology PUQpress Скачать руководство пользователя страница 22

Страница: 22 / 25

6 EXPLODED VIEW: TOTAL ASSEMBLY

3880 g

REVISIONS

REV.

DESCRIPTION

DATE

APPROVED

---

28-8-2016

L.Pluimers

ITEM

NO.

PART NAME

DESCRIPTION

QTY.

1 1-210-0022-1-111-1-

B_main_housing_top_cover

Main housing - top cover

1-210-0030-1-111-1-

B_ground_coffee_basket

Coffee ground basket

3 1-410-0002-1-111-1-

A_induction_sensor_connector

Elec. Assy: Induction

connector

1-110-0025-1-111-1-

A_rivet_bushes_crimp_nut

Rivet bushes crimp nut

5 1-210-0035-1-111-1-

B_anti_slip_foot

Anti-slip foot

1-210-0061-1-111-1-

A_product_information_sticker

Production information sticker

1-110-0001-1-111-1-

A_ACDC_converter

AC/DC converter

8 1-210-0101-1-111-1-

B_motor_controller

Motor controller

9 1-110-0022-2-111-1-

A_cross_head_M3x8

Cross head screw M3x8

10 1-110-0027-2-111-1-

A_hex_cap_screw_M5x25

Hexagon head cap screw M5x25

11 1-110-0029-2-111-1-

A_cross_head_M4x10

Cross head screw M4x10

12 1-110-0026-111-1-

A_hex_cap_screw_M5x12

Hexagon head cap screw M5x12

13 1-110-0032-1-111-1-

A_toothed_lock_washer_M5

Toothed lock washer M5

14 1-110-0034-

1_hex_button_head_M6x14

Hexagon button head screw M6x14

15 1-110-0035-1-111-1-

A_mudwing_repair_washer_M6x14

Mudwing repair washer, M6x14x1.5

1-110-0036-2-111-1-A_washer_M6

Washer M6

17 1-110-0037-1-111-1-

A_set_screw_M5x12

Set screw M5x12

18 1-110-0015-1-111-1-

A_power_entry_connector_C14

Euro socket

1-210-0026-1-111-1-

B_motor_controller_support_fram

Motor controller - support frame

20 1-210-0005-3-111-1-

C_upper_clamp

Upper clamp, chromium plated

21 1-210-0060-1-111-1-

B_display_sticker

Display sticker

22 1-110-0014-1-111-1-

A_on_off_switch

On/off switch

23 1-110-0031-2-111-1-

A_plastic_screw_4x12

PT screw for plastic

24 1-210-0001-3-111-1-D_main_body

Main body

25 1-210-0020-2-111-1-

A_main_housing_back_cover

Main housing - back cover

26 1-210-0021-1-111-1-

D_main_housing_middle_cover

Main housing - middle cover

27 1-110-0023-1-111-1-

A_magnet_10mm

Neodymium magnet

28 1-110-0024-1-111-1-

A_cover_for_magnets

Label 38x23mm

29 1-110-0038-1-111-1-

A_spring_lock_washer_M3

Spring lock washer M3

30 1-210-0044-1-111-1-B_Mylar_foil

Mylar A foil

31 1-110-0073-1-111-1-

A_screw_2.9x12mm

Metal screw 2.9x12

32 1-110-0074-1-111-1-

A_toothed_lock_washer_M3

Toothed lock washer M3

33 1-310-0001-1-111-1-D_drive_unit

Mech. Assy: drive unit

34 1-210-0015-2-111-1-

C_lower_clamp

Lower clamp

35 1-210-0040-1-111-1-

C_counterweight

Counter weight

36 1-410-0005-2-111-1-

A_grounding_cable

Elec. assy: Grounding cable

37 1-410-0006-2-111-1-

A_on_off_switch_cable_brown

Elec. assy: on/off switch cable,

brown

38 1-410-0008-2-111-1-

A_on_off_switch_cable_blue

Elec. assy: on/off switch cable,

brown

39 1-110-0089-1-111-1-A_stud_M3x30

Stud M3x30mm

1-210-0036-1-111-1-1-

A_shielding_plate_AC_DC_conve

rter

EMC shielding plate

41 1-410-0001-2-111-1-

B_input_cable_converter

Elec. assy: Input cable converter

42 1-410-0009-2-111-1-

A_earthing_cable_DC_motor

Elec. assy: Earthing cable DC motor

Puqpress 58mm EURO

WEIGHT:

Page: 1 of 1

SCALE 1:1

Part number:.

Part name:

DO NOT SCALE DRAWING

MATERIAL:

Geometric dimensioning

and tolerancing according

to NEN-ISO1101 and NEN-

ISO 2768-1-mK

1-000-0101-2

FINISH:

Barista Technology B.V.

Oostelijke handelskade 731

1019 BW Amsterdam

The Netherlands

Doc: 110-1

Содержание PUQpress


























Результаты поиска

Содержание PUQpress

Отзывы:

Похожие инструкции для PUQpress

Бренды по названию

Популярные бренды

Barista Technology PUQpress, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание PUQpress

Отзывы:

Похожие инструкции для PUQpress

Бренды по названию

Популярные бренды