background image

Manual 2100-639A 

Page 

18 of 28

SERVICE

FIGURE 7

Fan Blade Setting

TABLE 2

Fan Blade Dimension

REMOVAL OF FAN SHROUD

1.  Disconnect all power to the unit.

2.  Remove the screws holding both grilles, one on 

each side of unit, and remove grilles.

3.  Remove nine (9) screws holding fan shroud to 

condenser and bottom.

4.  Unwire condenser fan motor.

5.  Slide complete motor, fan blade and shroud 

assembly out the left side of the unit.

6.  Service motor/fan as needed.

7.  Reverse steps to reinstall

.

R-410A REFRIGERANT CHARGE

This unit was charged at the factory with the quantity 
of refrigerant listed on the serial plate.  AHRI capacity 
and efficiency ratings were determined by testing with 
this refrigerant charge quantity.

The pressure table on the following page shows 
nominal pressures for the units.  Since many 
installation specific situations can affect the pressure 
readings, this information should only be used by 
certified technicians as a guide for evaluating proper 
system performance.  They shall not be used to adjust 
charge.  If charge is in doubt, reclaim, evacuate and 
recharge the unit to the serial plate charge.

"A"

AIRFLOW

MIS-1724

Model

Dimension

A

H24

1.00"

H36

1.25"

H42
H48
H60

1.75"

FAN BLADE SETTING DIMENSIONS

The correct fan blade setting for proper air delivery 
across the outdoor coil is shown in Figure 7.  Refer to 
Table 2 for unit specific dimension.

Any service work requiring removal or adjustment in the 
fan and/or motor area will require that the dimensions 
below be checked and blade adjusted in or out on the 
motor shaft accordingly.

Содержание H24A4-A





























Отзывы: