background image

Manual 2100-670 

Page 

6 of 32

FIGURE 2

TEC-EYE Connection to Unit Control

Modular Phone Connector for 
TEC-EYE Hand-Held Diagnostic Tool

USING THE TEC-EYE

TM

TEC-EYE Hand-Held Diagnostic Tool

The microprocessor control used in the FUSION-TEC 
wall-mount air conditioners allows for complete control 
and monitoring through the use of the provided TEC-
EYE hand-held monitor. This comprehensive service 
tool utilizes the latest in state-of-the-art technology 
including a large, easy-to-read backlit LCD graphic 
display.
The menu driven interface provides users the ability 
to scroll through two menu levels: Quick Menu and 
Main Menu. The menus permit the user to easily view, 
control and configure the unit.
The controller is completely programmed at the factory; 
the default setpoints and their ranges are easily viewed 
and adjusted from the TEC-EYE display. The program 
and operating parameters are permanently stored 
on FLASH-MEMORY in case of power failure. The 
controller is designed to manage temperature levels to 
a user-defined setpoint via control output signals to the 
wall mount air conditioning system.
The TEC-EYE connects to the wall-mount unit control 
board via an RJ11 modular phone connector as shown 
in Figure 2.

ALARM KEY

Allows viewing of active alarms
Silences audible alarms
Resets active alarms

MENU KEY

Allows entry to Main Menu

ESCAPE KEY

Returns to previous menu level
Cancels a changed entry

UP KEY

Steps to next screen in the display menu
Changes (increases) the value of a modifiable field 

ENTER KEY

Accepts current value of a modifiable field
Advances cursor

DOWN KEY

Steps back to previous screen in the display menu
Changes (decreases) the value of a modifiable field

FIGURE 1

TEC-EYE (Bard P/N 8301-059) Display and Interface (Status Screen Shown)

NOTE:

 

Screenshots shown in this manual reflect 

default settings (when applicable).

When not being used, the TEC-EYE hand-held 
diagnostic tool should be stored inside or near the 
LV1000 controller. Do not let the TEC-EYE leave the 
shelter.

ALARM KEY

MENU KEY

ESCAPE KEY

DOWN KEY

UP KEY

ENTER KEY

Содержание FUSION-TEC HR58APB

































Отзывы: