manualshive.com logo in svg
background image

Manual 2100-670 

Page 

7 of 32

TEC-EYE Menu Structure

Quick Menu
 Setpoints
 Information
 

Alarm Log

Main Menu
 

System Configuration

 

Advanced System Configuration

 

I/O Configuration

 On/Off
 

Alarm Logs

 Settings
 Logout
In addition to the menu structure above, there are also 
Status and Alarm screens.

TEC-EYE Acronyms

MAT – Mixed air temperature
RAT – Return air temperature
OAT – Outdoor air temperature
OAH – Outdoor air humidity
Blower – Indoor blower status
Damper – Free cooling damper position status
CL1 – Compressor stage 1 status
CL2 – Compressor stage 2 status
H1 – Heater stage 1 status
H2 – Heater stage 2 status
ODP – Calculated outdoor dew point
FC – Free cooling status
RN – Component run time in minutes in last hour
ST – Number of start requests in last hour

NOTE:

 

Digital refers to On/Off whereas analog is a 

variable input.

Status Screen

The Status screen is the default start-up screen and 
also the return screen after 5 minutes of no activity. 
The screen can be accessed any time by pressing the 
ESCAPE key repeatedly.
The wall-mount unit address is displayed in the upper 
right corner on the Status screen (see Figure 1). The 
Status screen also shows the current date, time, return 
air temperature, mixed air temperature, outdoor air 
temperature, outdoor humidity and outdoor dew point 
conditions. Blower, damper and unit status are also 
displayed. See Table 1 for wall-mount unit status 
messages.
The Quick Menu is accessible from the Status screen. 
Setpoints, Information and Data (Alarm) Log are 
available through the Quick Menu. Pressing the UP or 
DOWN keys while on the Status screen will change the 
Quick Menu icon displayed (see Figure 3). Press the 
ENTER key when the desired icon is displayed.

Quick Menu

Setpoints

From this screen, the unit heating and cooling 
setpoints can be changed. 
The 

LV1000

 setpoints will determine the cooling and 

heating setpoints when 

communicating with the wall-

mount units

. The 

unit

 cooling and heating setpoints 

will determine the cooling and heating setpoints when 

in stand alone mode

If at any time the unit(s) loses communication with the 
LV1000 controller, the unit(s) will go into stand alone 
mode.

FIGURE 3

Quick Menu Icons

Data Log

Unit Information

Setpoints

Message

Description

Orphan Stby

Unit is on and in orphan mode with 

no calls for heating or cooling

Power Loss

Unit is operating under power loss 

conditions (inverter model)

Freecooling

Unit is actively economizing

Cooling

Unit is actively mechanical cooling

Heating

Unit is actively heating

Dehum Mode

Unit is actively dehumidifying

Off by Alarm

Unit has major fault preventing 

operation

Off by Keyboard

Unit has been turned off by 

local user

Off by LV

Unit has been turned off by the 

supervisory controller

Manual Mode

There is an active override on the 

system

Test Mode

System is performing a run test

Emergency Vent

Unit has active hydrogen alarm 

and is actively exhausting the air to 

outside

Emergency Off

Unit has active smoke alarm and 

Emergency Shutdown is active

TABLE 1

Unit Status Messages

Содержание FUSION-TEC HR58APB

































Отзывы: