![background image](http://html.mh-extra.com/html/barco/xdm/xdm_installation-manual_474400013.webp)
13
R5914477 /00
XDM
•
Remove all power from the projector and refer servicing to qualified service technicians under the following
conditions:
-
When the power cord or plug is damaged or frayed.
-
If liquid has been spilled into the equipment.
-
If the product has been exposed to rain or water.
-
If the product does not operate normally when the operating instructions are followed. Adjust only those
controls that are covered by the operating instructions since improper adjustment of the other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to normal operation.
-
If the product has been dropped or the cabinet has been damaged.
-
If the product exhibits a distinct change in performance, indicating a need for service.
•
Replacement parts: When replacement parts are required, be sure the service technician has used original
Barco replacement parts or authorized replacement parts which have the same characteristics as the
Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire,
electric shock or other hazards. Unauthorized substitutions may void warranty.
•
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
Safety Data Sheets for Hazardous Chemicals
For safe handling information on chemical products, consult the Safety Data Sheet (SDS). SDSs are available
upon request via [email protected].
On the reinforcement frame
•
The XDM reinforcement frame is exclusively designed for the XDM projectors and can thus not be used on
other equipment.
•
The reinforcement frame is single use. While certain brackets on the frame can be removed in order to
remove the front, rear and top cover of the projector, it is not allowed to disassemble the reinforcement
frame itself.
•
It is not allowed to stack the reinforcement frames of the XDM projector on top of each other, nor is it
allowed to suspend them from each other.
•
When the projector is suspended from a truss, a minimum of four (4) clamps must be used to secure the
projector. The clamps must be fixed to the projector frame. Use a truss which is capable of handling five (5)
times the complete load of the system. Also use clamps that are capable of handling five (5) times the
complete load of the system.
•
It is the responsibility of the installer to suspend the reinforcement frame in a safe and secure fashion.
Safety cables must be applied according to local regulations and standards. Safety cables must be
dimensioned for the applicable load and no drop distance is allowed or must be limited as much as
possible.
•
When the safety cables have undergone a heavy shock, invisible damage may have occurred to the safety
cables. In this case the safety cables must be replaced.
Содержание XDM
