![background image](http://html.mh-extra.com/html/barco/vision-708-9002357/vision-708-9002357_installation-manual_474391015.webp)
Installation Set Up
4-3
5976026A BARCOVISION 708 200499
ADJUSTMENT MODE
Select a path from below :
IRIS
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
Source 01
Select with or
then <ENTER>
<EXIT> to return.
A : Horizontal scan inversion
Three connectors are used, one for each horizontal
deflection coil. When changing the horizontal scan,
insure that all three connectors are set in the same
position. See position of the connectors for the
corresponding projector configuration.
B : Vertical scan inversion
Three connectors are used, one for each vertical
deflection coil. When changing the vertical scan,
insure that all three connectors are set in the same
position. See position of the connectors for the
corresponding projector configuration.
Top view of the connectors; upper three connectors
for horizontal scan inversion, lower three for vertical
scan inversion.
C : Convergence connectors
Three connectors are used. The position of these connectors has
to be changed when switching from one configuration to another.
With an open chassis, for a
front-table
or a
rear ceiling
configuration,
the connectors must be plugged in with the
contacts upwards
(away
from the tubes). For a
front-ceiling
or
rear-table
configuration, the
connectors must be plugged in with the
contacts facing the tubes
After scan inversion, close the chassis and close the top cover. Reconnect the power
cord to the wall outlet.
Note
Switching over from floor to ceiling or vice versa requires a complete readjustment of
picture geometry and convergence.
Check of the correct connector position
Note : this check procedure can only be done after power (mains) connection. So, first
continue with the
projector set up
and the
connections
and then return to this checking
procedure.
To start the checking procedure :
1. Switch on the projector
2. Press
ADJUST
to start up the adjustment mode.
3. Push the cursor key
é
or
ê
to select 'Service'
4. Press
ENTER
. The service menu will be displayed.
5. Push the cursor key
é
or
ê
to select 'PROJECTOR SET UP'
6. Press
ENTER
.
7. Push the cursor key
é
or
ê
to select 'IDENTIFICATION'
8. Press
ENTER
. On this screen, information is given about the projectors configuration.
Configuration when leaving the factory : ceiling/front configuration.
Select with or
then <ENTER>
<EXIT> to return.
SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
)URQW7DEOH
)URQW&HLOLQJ
5HDU7DEOH
5HDU&HLOLQJ
Horizontal
scan
connectors
Vertical scan
connectors
&RQWDFWVLGH
Proj. address : 001
Soft. Version : 6.00
Config. : Ceiling
Front
Baudrate PC : 9600
Text : ON
Serial No. : 103589552
VISION 708
Содержание Vision 708 9002357
