![background image](http://html1.mh-extra.com/html/barco/r9002357/r9002357_owners-manual_4229243020.webp)
Controlling
4-3
5976025A BARCOVISION 708 200499
352-(&725
$''5(66
Projector address
a. Software set up of the projector address.
See 'Change Projector Address' in chapter 'Service mode'.
Every projector requires an individual address between 0 and 255 which is set in the Service mode. Only projectors with addresses between
0 and 9 can be controlled with the RCU.
b. How to control the projector.
The projector's address may be set to any value between 0 and 255. When the address is set, the projector can be controlled controlled now:
- the RCU for addresses between 0 and 9.
- Computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.
Note : A projector will respond to an RCU set to an address of '0' regardless of what address is set in the projector itself.
c. Using the RCU.
The RCU is default programmed with address 0, 'zero address'. With that 'zero address' programmed into the RCU, every projector, without
exception will listen to the commands given by this RCU. If it is necessary to control a specific projector, than enter the projector address into
the RCU (only when that address is between 0 and 9). The projector with the corresponding address will listen to that specific RCU.
Displaying a Projector Address.
Press the
ADDRESS
key (recessed key on the RCU) with a pencil. The projector's address will be
displayed in a 'Text box'. This text box disappears after a few seconds.
To continue using the RCU with that specific address, it is necessary to enter the same address with
the digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For
example : if the Address key displays projector address 003, then press "3" digit button on the RCU
to set the RCU's address to match the projector's address. Do not press 003 digits. This will address
the remote control to '0' and control all projectors in the room.
If the address is not entered within 5 seconds, the RCU returns to its default address (zero address)
and control all projectors in the room.
How to program an address into the RCU?
Press the
ADDRESS
key (recessed key on the RCU) with a pencil and enter the address with the digit
buttons within 5 seconds after pushing the address key. That address can be any digit between 0
and 9.
Source No Projector input
Press button
1
Comp. Video
1
2
S-Video
2
3
RGBS or RGsB
3
3
RGB3S or RG3sB
4
3
(R-Y)Y(B-Y)S or
(R-Y)Ys(B-Y)
5
3
(R-Y)Y(B-Y)3S or
(R-Y)Y3s(B-Y)
6
Input selection
Two possible ways of selecting an input :
a) With the digit buttons on the RCU, it is possible to select one of the
four input sources, Video, S-Video, RGsB or RGBS, RG3sB or
RGB3S, (R-Y)Ys(B-Y) or (R-Y)Y(B-Y)S, (R-Y)Y3s(B-Y) or (R-Y)Y(B-
Y)3S.
Содержание r9002357
Страница 1: ...OWNER S MANUAL R9002357 R9002358 VISION 708 ...
Страница 2: ...BARCO PROJECTION SYSTEMS Date 200499 OWNER S MANUAL Art No R5976025A R9002357 R9002358 VISION 708 ...
Страница 11: ...Location and Function of Controls 2 4 5976025A BARCOVISION 708 200499 ...
Страница 23: ...Controlling 4 6 5976025A BARCOVISION 708 200499 ...