![background image](http://html1.mh-extra.com/html/barco/r9001260/r9001260_owners-manual_4217700016.webp)
Connections
5-2
5975967 BARCODATA 9200 220198
0
I
WARNING
Lamp run time is 1000 hours
Operating the lamp longer
than 1000 hours may damage
the projector.
Please replace the lamp
<ENTER> to confirm²
Lamp run time
980 hours
Lamp Run Time
When the total run time of the lamp is 970 hours or more, the following message will be
displayed for 1 minute. This message will be repeated every 30 minutes. Press EXIT to
remove the message before the minute is over.
When the total run time of the lamp is 1000 hours or more, the following message, with
the exact run time is displayed on the screen.
Lamp run time is 1000 hours. Operating the lamp longer than 1000 hours may damage
the projector. Please replace the lamp.
When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min.
The total lifetime of the lamp for a safe operation is 1000 hours max. (normal power mode).
Do not use it longer. Replace always with a same type of lamp. Call a BARCO authorized
service technician for lamp replacement.
Warning : Using a lamp for more than 1000 hours is dangerous, the
lamp could explode.
Switching to stand-by.
When the projector is running and you want to go to stand-by, press
the stand-by key.
Switching off
To switch off:
- press first
STANDBY
key and let cool down until the fans
stop blowing ( or at least 15 min).
- switch off the projector with the power switch.
WARNING : When switching to standby, never restart projec-
tion (hot restrike) within the first 3 minutes to avoid damage
to the lamp.
Input connections.
The projector has modular input facilities. The input slots
can be filled up with the following modules :
Video, S-video input
order no. R9827900
RGBS/RGsB analog input
order no. : R9827910
RGB3S/RG3sB input
order no. : R9827920
Component Video input
order no. : R9827930
The sequence of insertion has no importance, exept when
using a RCVDS or VS05. It is even perfectly possible to
insert several input modules of one type.
Note : When using RCVDS05 or VS05, the input configu-
ration of the projector must be as follows:
Slot 1 : video input module
Slot 2 : RGB analog input module
Slot 3 : Component input module
Input module insertion into the projector :
- Power down the projector and disconnect the power cord
from the wall outlet.
- Remove the dummy plate covering the chosen input slot
by turning out both screws.
- Slide the input module in the free slot. Insure the module
is seated correctly in the guide grooves.
- Press on both handles of the input module until the module
plug seats in the connector of the projector.
- Secure the input module by tightening both retaining
screws.
- Reconnect the power cord to the wall outlet and switch
on the projector.
The new installed module can be selected with the digit buttons on
the RCU or the local keypad.
Содержание R9001260
