Barco MDSC-2324 DDI, Руководство пользователя

Страница: 66 / 78

K5903252 (451920612633) /02 MDSC-2324
66
Emissions test
Compliance
Electromagnetic environment –
Guidance
supplies buildings used for
domestic purposes.
RF emissions
CISPR 11 Class A The MDSC-2324 MNA version is
suitable for use in all
establishments, including domestic
establishments and those directly
connected to the public low-voltage
power supply network that supplies
buildings used for domestic
purposes.
Harmonic emissions
IEC 61000-3-2 Not applicable: power consumption
less than 75W
Voltage fluctuations/ flicker
emissions
IEC 61000-3-3 Complies
This MDSC-2324 complies with appropriate medical EMC standards on emissions to, and interference from
surrounding equipment. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Interference can be determined by turning the equipment off and on.
If this equipment does cause harmful interference to, or suffer from harmful interference of, surrounding
equipment, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna or equipment.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
Electromagnetic immunity
The MDSC-2324 is intended for use in the electromagnetic environment (IEC 60601-1-2 4 th edition) specified
below. The customer or the user of the MDSC-2324 should assure that it is used in such an environment.
Immunity test
IEC 60601-1-2 4 th edition
(2014)
Test levels
Compliance level
Electromagnetic
environment
– guidance
Electrostatic discharge
(ESD)
IEC 61000-4-2 ± 8kV contact
± 15kV air ± 8kV contact
± 15kV air Floors should be wood,
concrete or ceramic tile. If
floors are covered with
synthetic material, the
relative humidity should be
at least 30%
Electrical fast transient/
burst
IEC 61000-4-4 ± 2kV for power supply
lines
± 1kV for input/ output
lines ± 2kV for power supply
lines
± 1kV for input/ output
lines Mains power quality
should be that of a typical
commercial or hospital
environment
Surge
IEC61000-4-5 ± 1 kV line(s) to line(s)
± 2 kV line(s) to earth ± 1 kV line(s) to line(s)
± 2 kV line(s) to earth Mains power quality
should be that of a typical
commercial or hospital
environment
Voltage dips, short
interruptions and voltage
variations on power supply
input lines
IEC 61000-4-11 < 5% U
T
1 (> 95% dip in
U
T
) for 0.5 cycle
40% U
T
(60% dip in U
T
) for
5 cycles
70% U
T
(30% dip in U
T
) for
25 cycles
< 5% U
T
(>95% dip in U
T
)
for 5 seconds
< 5% U
T
(> 95% dip in U
T
)
for 0.5 cycle
40% U
T
(60% dip in U
T
) for
5 cycles
70% U
T
(30% dip in U
T
) for
25 cycles
< 5% U
T
(>95% dip in U
T
)
for 5 seconds
Mains power quality
should by that of a typical
commercial or hospital
environment. If the user of
the MDSC-2324 requires
continued operation
during power mains
interruptions, it is
recommended that the
MDSC-2324 be powered
from an uninterruptible
power supply or a battery.
Important information
1: is the a.c. mains voltage prior to application of the test level.