![background image](http://html1.mh-extra.com/html/barco/graphics-808s/graphics-808s_isntallation-manual_4216458024.webp)
Source connections
7-2
5975996 BARCOGRAPHICS 808s 241197
Connecting a S-Video (or Composite Video)
source to Port 2
Separate Y-luma/C-chroma signals for higher quality playback of
Super VHS signals can be connected to Port 2 . The composite video
can also be connected to this port.
To select the S-video input :
Press the
numeric button 2
on the RCU or the local keypad
.
In case of using Port 2 for connecting the Composite Video, the
selection of this source have to be done inside the "Picture Tuning"
menu. Please refer to the Owner's Manual of this projector.
75 W Termination Switch for S-video
Terminate the S-video input of the projector using the 75 W switch
next to the S-video input when the projector operates alone or when
the projector is the last unit in a loop-through configuration.
The switch is set to "ON" : signal terminated.
The switch is set to "OFF" : signal not terminated.
Connecting a RGB Analog source to Port 3
Connect a RGB Analog signal via an interface (e.g. RGB 120MHz
interface, part number 98 26570) to Port 3: RGB analog input with
automatic sync detection (Separate H and V sync inputs, with
composite sync input or with sync signals on green).
Pin configuration of the D9 (male) connector of the Analog input :
1
not connected
2
ground RGBS
3
RED
4
GREEN
5
BLUE
6
ground RGBS
7
ground RGBS
8
Horizontal /composite sync
9
Vertical sync
To select the RGB analog Input :
Press the
numeric button 3
on the RCU or the local keypad
.
S1 Force Negative Sync
(ON=yes)
R81
Hsync
R101
Vsync
R41
(Blue)
R21
(Green)
R1
(Red)
S2 Blue in Green (ON=yes)
Line termination 75
Ω
resistors
75
Ω
Termination Switch
1
2
3
4
4 pin connector configurations:
For S-video:
Pin 1: earth(ground) luminance
Pin 2: earth(ground) chrominance
Pin 3: luminance signal(Y)
1Vpp
±
3dB
Pin 4: chrominance signal(C)
300mVpp
±
3dB
For video:
Pin 1: earth(ground) video
Pin 2: not connected
Pin 3: video signal
Pin 4: not connected
Locations of the Termination Resistors and Switches
on the RGB Input Auto Sync Tracking Module
When changing a switch position or removing a resistor, turn off the
projector and unplug the power cord from the wall outlet.
75 W Termination resistors
In case of chaining (loop-through) the projectors, the 75W line
termination resistors must be removed from the RGB Input Auto Sync
Tracking Module when the projector is NOT the last unit in the chain.
In case of a stand-alone projector, do not remove the resistors.
75 W resistors on the module :
line terminated.
75 W resistors removed
:
line not terminated.
21
2))
POWER / MAINS
SHULSKHUDOV
5
*
% &RPS+6\QF96\ QF
COMM. POR T
PORT 3
P O RT 4/ 5
9QRP
,QRP
)UHT
6HHLQVWDOODWLRQLQVWUXFWLRQVEHIRUHFRQQHFWLQJWRWKHVXSSO\
9RLUODQRWLFHGLQVWDOODWLRQDYDQWGHUDFFRUGHUDXUpVHDX
9
$PS
+]
6 9 '(2
2 21
2KP
9 '(2
J U H H Q R S H U D WL R Q
U H G V WD Q G E \
PORT 2
POR T 1
2 21
2KP
PROJ ECTOR MOD E
LQYHU
RKPWHUP
7KLVGHYLFHFRPSOLHVZLWKSDUWRI
WKH)&&UXOHV2SHUDWLRQLVVXEMHFWWR
IROORZLQJWZRFRQGLWLRQV7KLV
G LF \QRWF V K
I OLQW
I
QF QGWKLVG LF VW
FF W Q\LQW I
QF F L G
LQFO GLQJLQW I
QF WK W \F V
QG VL GR
WLRQ
RGB 120MHz interface
All manuals and user guides at all-guides.com