![background image](http://html1.mh-extra.com/html/barco/f80-q7/f80-q7_user-manual_4121408009.webp)
1. Safety
To prevent personal injury
•
To prevent injury and physical damage, always read this manual and all labels on the system before powering the projector or
adjusting the projector.
•
To prevent injury, take note of the weight of the projector. Minimum 2 persons are needed to carry the projector. The projector
weights about ±26 kg (±57 lbs) without lens and rigging frame.
•
To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
•
Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.
•
Warning: extremely high brightness projector
: This projector embeds extremely high brightness (radiance) lasers; this laser
light is processed through the projectors optical path. Native laser light is not accessible by the end user in any use case. The
light exiting the projection lens has been diffused within the optical path, representing a larger source and lower radiance value
than native laser light. Nevertheless the projected light represents a signi
fi
cant risk for the human eye when exposed directly
within the beam. This risk is not speci
fi
c related to the characteristics of laser light but solely to the high thermal induced energy
of the light source; which is comparable with lamp based systems.
Thermal retinal eye injury is possible when exposed within the Hazard Distance. The Hazard Distance (HD) is de
fi
ned from
the projection lens surface towards the position of the projected beam where the irradiance equals the maximum permissible
exposure as described in the chapter "High Brightness precautions: Hazard Distance (HD)", page 8 .
•
Based on international requirements, no person is allowed to enter the projected beam within the zone between the projection
lens and the related Hazard Distance (HD). This shall be physically impossible by creating suf
fi
cient separation height or by
placing optional barriers. Within the restricted area operator training is considered suf
fi
cient. The applicable separation heights
are discussed in "High Brightness precautions: Hazard Distance (HD)", page 8 .
•
Don’t put your hand in front of the beam.
•
This product contains no user serviceable parts. Attempts to modify/replace mechanics or electronics inside the housing or
compartments will violate any warranties and may be hazardous.
•
A special device (“rigged frame”) based on an external frame must be used when the projector is deployed in a hanging con-
fi
guration, or when several projector must be stacked. See installation manuals for the correct use of these devices.
•
Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and
possible injury to the user.
•
It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they have become
visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.
•
Cooling liquid circuit.
The projector contains a cooling circuit
fi
lled with Green Ethylene glycol diluted (53% Glycol – 47%
Demi water). When the cooling circuit leaks, switch off the device and contact quali
fi
ed service personnel. The liquid is not for
household use. Keep out of reach of children. Harmful by oral intake. Avoid exposure to pregnant women. Avoid contact with
eyes, skin and clothing. Avoid inhale of the noxious fumes.
•
Never point or allow light to be directed on people or re
fl
ective objects within the HD zone.
•
All operators shall have received adequate training and be aware of the potential hazards.
•
In case of using an external cooling system position the hoses of the cooling system so that they will not be tripped over, pulled,
or contact hot surfaces.
To prevent
fi
re hazard
•
Do not place
fl
ammable or combustible materials near the projector!
•
Barco projection products are designed and manufactured to meet the most stringent safety regulations. This projector radiates
heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe. Exposing
fl
ammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that material,
resulting in a
fi
re. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the
projector whereby no
fl
ammable or combustible materials are present. The exclusion zone in the exhaust area must be not
less than 100 cm (40”). The exclusion zone on the intake area must be not less than 50 cm (20”).
•
Do not place any object in the projection light path at close distance to the projection lens output. The concentrated light at the
projection lens output may result in damage,
fi
re or burn injuries.
•
Do not cover the projector or the lens with any material while the projector is in operation. Keep
fl
ammable and combustible
materials away from the projector at all times. Mount the projector in a well ventilated area away from sources of ignition and
out of direct sun light. Never expose the projector to rain or moisture. In the event of
fi
re, use sand, CO
2
or dry powder
fi
re
extinguishers. Never use water on an electrical
fi
re. Always have service performed on this projector by authorized Barco
service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco replacement parts as they may
degrade the safety of this projector.
•
Ensure no misalignment can occur. Prolonged exposure of wooden walls at close distance (< 20 cm) can represent a
fi
re risk.
After alignment the projector shall be securely mounted to the pedestal.
•
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect
it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the
projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat
register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
•
Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent hot exhaust air from
projector and cooling system to the outside of the building.
•
Let the projector cool completely before storing. Remove cord from the projector when storing.
R5906852 F80 SERIES 21/09/2017
5
Содержание F80-Q7
