![background image](http://html1.mh-extra.com/html/barco/f80-q7/f80-q7_user-manual_4121408030.webp)
4. Getting Started
The background image of the startup screen and info screens can be changed with Projector Toolset with an
installed F80 plug-in.
Description
Plug the 3-prong plug of power cord into a grounded AC outlet. The projector will go to
READY
mode. During this stage the system
boots and performs the internal check of the boards. The Power
On/Off button
will BLINKING WHITE until
READY
mode is achieved.
Once in
READY
mode, the
Power On/Off
button will be lit WHITE.
4.3.3
Going from READY to ON
Description
Press the
Power On/Off
button on the projector, or the
Power On
button on the remote control. The projector will power
ON
. The
Power On/Off
button will BLINK BLUE during the transition from
READY
to
ON
. Once the projector is on, the
Power On/Off
button
will be lit BLUE.
4.3.4
Going from ON to READY
Description
Press the
Power on/off
button on the projector, or the
Power On
button on the remote control. The projector will power down through
a cool down phase. The
Power on/off
button will BLINK WHITE during the transition from
ON
to
READY
. Once the projector is in
READY
, the
Power on/off
button will be lit WHITE.
4.3.5
Going from READY to ECO standby
Description
If ECO Standby mode is enabled in the service menu (refer to the section "GUI - system settings/Standby ECO", in User Guide) the
projector will automatically go to
ECO
standby mode after a time-out (default 15 minutes). All electronics (including fans, pumps,...)
go down except for a very small wake up controller. The
Power on/off
button will FLASH WHITE every second.
4.3.6
Going from ECO to ON
Description
Press the
Power on/off
button on the projector, or the
Power On
button on the remote control or do a wake on LAN. The projector
goes from
ECO
directly to
ON
. The projector will go through the same booting phase as on power plugging, then do the transition
from
READY
to
ON
. Of course startup-time will be longer then from
READY
to
ON
.
4.4
Status overview
Description
Once the projector is started, press
Status
to get an overview of parameters such as :
•
Chosen source
•
Current resolution and refresh rate
•
Device serial number and article number
•
Current
fi
rmware version and model name
•
Current illumination (in percentage)
•
Lamp runtime in hours
•
Chosen communication method and IP address (if connected)
•
Warp status
•
Environmental temperature
26
R5906852 F80 SERIES 21/09/2017
Содержание F80-Q7
