R5909934 /00
E2 Lite and EC-40
172
check all Ethernet connections. After checking connections, if devices still report
“
Not Connected,
”
use the
procedure
7.4 Return to factory default
General
Prior to performing any setup procedures, it is recommended that you perform a factory reset
—
in order to
reset all input, output and source mappings to their default values.
Particularly for customers in the events and rental marketplace, this procedure guarantees that any previous
input setups and memory registers (e. g., those that may have been programmed by other users) are
completely cleared from system memory.
If you are continuing an event (for example, day two of a three-day event), you do not need to
perform a factory reset. However, if you do elect to perform a factory reset, ensure that you have
backed up your system. for details, please refer to the procedure
“
, page
Prerequisite
•
Ensure that you are familiar with the
Reset Menu
. For details on all menus, please refer to chapter
Restoring Factory Default Settings
, page 62.
Restoring factory settings
To restore all default settings to the Event Master series processor, use the following procedure:
1.
Select
Factory Reset
from the
Setup
Menu.
The
Factory Reset
Menu appears.
2.
Select
Factory Reset
to reset the entire system to its factory default values. Remember that all data will be
lost.
or
Select
Factory Reset, Save IP
to reset the entire system to its factory default values, but retains the IP
address of the unit.
A prompt appears, asking if you want to clear all configurations.
3.
Press
SEL.
The system turns off, then it reboots.
7.5 Communication setup
General
In this procedure, you will set up communication between the Event Master series processor and the local
network.
Prerequisite
•
Ensure that you are familiar with the
Ethernet Menu
. For details on this menu, please refer to chapter
”
, page 57.
Static IP or DHCP?
Use one of the following procedure to:
•
turn on the DHCP feature and query the DHCP server to obtain a valid IP address. A DHCP server must be
available on the local network.
•
or turn off the DHCP feature and set a static IP address for the Event Master series processor, along with a
subnet mask and gateway.
Содержание Event Master E2 Lite
