Barbecook SIESTA 412 223.9241.200, Инструкция пользователя

Страница: 15 / 111

www.barbecook.com 15
14 TROUBLESHOOTING
Problem Probable cause(s) Solution(s)
Not enough heat
• Gas supply not open
• Venturis not placed over openings of gas valves
• Burner openings blocked
• Gas cylinder (almost) empty
• Pressure regulator not connected correctly to
cylinder and/or hose
• Open gas supply
• Place venturis over openings of gas valves
• Clean burner openings or replace burners
• Replace gas cylinder
• Reconnect pressure regulator to cylinder and/or
hose
Excessive heat and/or flare-ups
• Food too fatty
• Fat in bowl, on burners or in grease trays
• Temperature too high
• Trim excess fat or set burners to a low position
• Clean bowl, burners and grease trays
• Set burners to a lower temperature and/or grill
food indirectly
Heat not distributed evenly
over grill surface Some heat differences are normal, see “10.6 Making
optimal use of the heat” and “10.7 Taking advantage
of the heat zones”. Probable cause(s) for big heat
differences:
• Appliance not preheated
• Preheat appliance
Yellow flames
• Burners or venturis blocked
• Salt on burners
• Appliance connected to butane
• Clean burners and venturis
• Clean burners
• Connect appliance to propane, using an
appropriate pressure regulator
Incomplete flame Burner blocked, pierced or rusted Clean or replace burner
Flash-backs (flames outside
venturis/at control knobs) Burners or venturis blocked
1 Close gas supply and set burners to OFF.
2 Let appliance cool down.
3 Clean burners and venturis.
Flames higher than edge of
bowl
• Lots of wind
• Gas cylinder (almost) empty
• Fat in bowl, on burners and/or in grease trays
• Put appliance with rear side towards wind
• Replace gas cylinder
• Clean bowl, burners and grease trays
Pressure regulator hums
• Hot weather
• New (full) gas cylinder
Not a hazard or defect. Should stop automatically
after a while.
Burner whistles when set to
LOW Gas injector, venturi and/or burner dirty Clean gas injector, venturi and burner
Impossible to light burner
(using either igniter or match)
• Burner or venturi blocked
• No gas supply
• Clean burner and venturi
• Open gas supply and press safety knob on
pressure regulator (not present on all regulators)
Impossible to light burner with
igniter
• No battery installed or battery not installed
correctly
• Igniter wiring not mounted correctly
• Electrode damaged
• Faulty ground
• Faulty igniter
• (Re)install battery, with terminals positioned
correctly
• Check and re-assemble all igniter connections
• Replace electrode
• Check and re-assemble electrodes, burners and
igniter
• Replace igniter
No sparks nor sound when
pressing igniter
• No battery installed or battery not installed
correctly
• Empty battery
• Igniter button not assembled correctly
• Faulty spark generator
• (Re)install battery, with terminals positioned
correctly
• Replace battery
• Re-assemble igniter button
• Replace spark generator
Only sound (no sparks) when
pressing igniter
• Faulty ground
• Burner and electrode too far apart
• Reconnect spark generator and electrodes
• Slightly bend electrode to bring it closer to the
burner
Sparks present that do not
originate from burners Faulty wiring Replace wiring
Sparks present, but not on all
electrodes and/or not powerful
enough
• Faulty ground
• Low battery
• Wet or broken electrodes
• Reconnect spark generator and electrodes
• Replace battery
• Dry electrodes with paper towels or replace
electrodes
!gas_siesta412_de.book Page 15 Friday, October 3, 2014 1:08 PM