Bante Instruments A Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 46

background image

31

I

A150/151

Measurements

Conductivity/

TDS/Salinity/

Resistivity Measurement

1.1 Rinse the conductivity electrode with distilled water. Place the

electrode (and temperature probe) into the sample solution and

stir gently. Ensure that no air bubbles on the sensor surface.

1.2 If the Auto-Read option in the setup menu is enabled, the meter

will automatically sense a stable reading and lock measurement,

the Hold icon appears on the screen. Press the key to resume

measuring.

If the option is disabled, the meter will continuously measure and

update the readings.

1.3 Wait for the measurement to stabilize and record the reading.
1.4 When all of the samples have been measured, rinse the electrode

with distilled water.

•

If the meter shows "Measured values exceed the range", replace

a conductivity electrode that is appropriate for the conductivity

range of the sample solution you are measuring.

•

To record the measurement at the predefined time intervals, refer

to the

Interval Readings

section on page 42.

Conductivity Ash Measurement

The A150 meter contains two conductivity ash measurement modes
including the Refined Sugar (ICUMSA GS2/3-17 standard) and Raw
Sugar (ICUMSA GS1/3/4/7/8-13 standard).
2.1 Prepare the sugar sample according to the selected ICUMSA

method.

2.2 Press the

Mode

key and the



key to select the either Refined

Sugar or Raw Sugar measurement mode.

2.3 Press the

Enter

key, the screen shows an input window and

waits for entering the conductivity of the used water for preparing

sugar solution (range: 0.0 to 100.0 µ S/cm).

2.4 Press the



/



key to set the value, press the

Enter

key to

confirm. When the setting is completed, the meter will begin the

measurement.

2.5 Rinse the conductivity electrode with distilled water, place the

electrode (and temperature probe) into the sample solution and

stir gently. Wait for the measurement to stabilize and record the

reading.

2.6 When all of the samples have been measured, rinse the electrode

with distilled water.

Conductivity ash measurement can only be performed at temperature
range from 15° C to 25° C. If the temperature reading is out of above
range, the meter will show a warning.

Electrode Maintenance

•

Rinse the conductivity electrode thoroughly with distilled water

after use.

•

Do not touch the platinum black coating on the sensor surface

and always keep it clean.

•

If there is a build-up of solids inside the sensor, remove carefully,

then recalibrate the electrode.

•

If you do not use the electrode for long periods, wipe clean with

a lint-free tissue and store the electrode in a dry and cool area.

•

If your electrode is model CON-10, store the electrode with tap

water. This sensor needs to be kept wet always.

Platinum black coating

«
...
30
31
32
33
34
...
»

Содержание A Series















































Отзывы:

Нет отзывов

Похожие инструкции для A Series

Бренд: ABB Страницы: 8

Бренд: ECO Sensors Страницы: 22

Бренд: ECO Sensors Страницы: 7

Бренд: F&F Страницы: 24

Бренд: QuadTech Страницы: 76

Clavinova CLP-311

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 3

Alto Horn, Baritone, Euphonium

Бренд: Yamaha Страницы: 22

Clavinova CLP-320

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

MTEK6000 Series

Бренд: Metretek Страницы: 81

Бренд: Hanna Instruments Страницы: 2

AirCon Service Mini Identifier R-1234yf

Бренд: Waeco Страницы: 132

Бренд: BANTE Страницы: 17

Бренд: E+E Elektronik Страницы: 4

Бренд: yellow jacket Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды