2. Write the lower word to the counter using control code 143 (0x8F).
Node Reg 15
0x8F
2
Node Reg 16
D3D9
Node Reg 7
0x8F
2
The counter has been preset to 20,567,001 (0x0139 D3D9).
Installing Your Sure Cross
®
Radios
Please refer to one of the following instruction manuals for details about successfully installing your wireless network components.
•
Performance Wireless I/O Network Instruction Manual:
Holding Registers
Counter 2 is DIP switch selectable between a rate or an event (default) counter. The rate counter uses I/O 5. The event counter
uses I/O 5 and 6.
Modbus Registers
EIP Registers
I/O Type
I/O Range
Holding Register
Representation (Dec)
Gateway
Node
Node
Min.
Max.
Min.
Max.
1
1 + (Node# × 16)
0 + (Node# × 8)
Instance 100 / N7
Counter 1 Discrete Value
0
1
0
1
2
2 + (Node# × 16)
1 + (Node# × 8)
Counter 2 Discrete Value
0
1
0
1
3
3 + (Node# × 16)
2 + (Node# × 8)
Counter 1 High Word
0
65535
0
65535
4
4 + (Node# × 16)
3 + (Node# × 8)
Counter 1 Low Word
0
65535
0
65535
5
5 + (Node# × 16)
4 + (Node# × 8)
Counter 2 High Word / Frequency
0
65535
0
65535
6
6 + (Node# × 16)
5 + (Node# × 8)
Counter 2 Low Word
0
65535
0
65535
7
7 + (Node# × 16)
6 + (Node# × 8)
Reserved
8
8 + (Node# × 16)
7 + (Node# × 8)
Device Message
9
9 + (Node# × 16)
0 + (Node# × 8)
Instance 112 / N14
NMOS OUT 1
0
1
0
1
10
10 + (Node# × 16)
1 + (Node# × 8)
NMOS OUT 2
0
1
0
1
11
11 + (Node# × 16)
2 + (Node# × 8)
NMOS OUT 5
0
1
0
1
12
12 + (Node# × 16)
3 + (Node# × 8)
NMOS OUT 6
0
1
0
1
13
13 + (Node# × 16)
4 + (Node# × 8)
Clear Counter 1
0
1
0
1
14
14 + (Node# × 16)
5 + (Node# × 8)
Clear Counter 2
0
1
0
1
15
15 + (Node# × 16)
6 + (Node# × 8)
Control Message
16
16 + (Node# × 16)
7 + (Node# × 8)
Reserved
Installing or Replacing the Battery (DX80...E Models)
To replace the lithium "D" cell battery or batteries in any integrated housing model, follow these steps.
CAUTION: There is a risk of explosion if the battery is replaced incorrectly.
1. Remove the four screws mounting the face plate to the housing and remove the face plate. Do not remove the radio cover
from the face plate.
2. Remove the discharged battery or batteries.
3. Install the new battery or batteries, verifying the positive and negative terminals align to the positive and negative terminals
of the battery holder mounted within the case.
4. After replacing the battery, allow up to 60 seconds for the device to power up.
5. Properly dispose of used batteries according to local regulations by taking it to a hazardous waste collection site, an e-
waste disposal center, or other facility qualified to accept lithium batteries.
Sure Cross
®
Performance Universal Counter P16E Node
6
www.bannerengineering.com - Tel: + 1 888 373 6767
P/N 199134 Rev. D