13.5 Note
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna,
•
Increase the separation between the equipment and receiving module,
•
Connect the equipment into an outlet on a circuit different from that to which the receiving module is connected,
and/or
•
Consult the dealer or an experienced radio/TV technician for help.
on p. 93. When integrated into OEM products, fixed antennas require installation preventing end-users from replacing them
with non-approved antennas. Antennas not listed in the tables must be tested to comply with FCC Section 15.203 (unique
antenna connectors), FCC Section 15.247 (emissions), and ISED RSS-Gen Section 6.8.
13.5 FCC and ISED Approved Antennas
WARNING: This equipment is approved only for mobile and base station transmitting devices. Antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or
operating in conjunction with any other antenna or transmitter.
This radio transmitter module RM1809 have been approved by FCC and ISED Canada to operate with the antenna types
listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater
than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Table 61: Certified Antennas for 900 MHz 1 Watt
Model Number
Antenna Type
Maximum Gain
Impedance
Minimum Required Cable/
Connector Loss
-
Integral Antenna
Unity gain
0
BWA-9O1-x
Omni, 1/4 wave dipole
≤2 dBi
50 Ω
0
BWA-9O2-C
Omni, 1/2 wave dipole, Swivel
≤2 dBi
50 Ω
0
BWA-9O6-A
Omni Wideband, Fiberglass Radome
≤8.2 dBi
50 Ω
2.2 dB
BWA-9O5-B
Omni Base Whip
≤7.2 dBi
50 Ω
1.2 dB
BWA-9Y10-A
Yagi
≤10 dBi
50 Ω
4 dB
13.6 FCC and ISED Certification, 2.4GHz
This equipment contains transmitter module DX80-2400 or SX243.
FCC ID:
UE300DX80-2400
IC: 7044A-DX8024
FCC ID: UE3SX243
IC: 7044A-SX243
HVIN: DX80G2 /
DX80N2 / SX243
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This device contains licence-exempt transmitters(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to
the following two conditions: (1) This device may not cause interference, and (2) This device
must accept any interference, including interference that may cause undesired operation of the
device.
Cet appareil contient des émetteurs/récepteurs exemptés de licence conformes à la norme
Innovation, Sciences, et Développement économique Canada. L’exploitation est autorisée aux
deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage, and (2) L’utilisateur
de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Sure Cross
®
DXM150 and 1500-Bx Wireless Controllers
www.bannerengineering.com - Tel: + 1 888 373 6767
93