Banner Sure Cross DX70 Скачать руководство пользователя страница 6

Страница: 6 / 35

DIP Switch

Discrete Input Type

NPN

2.1.2 Use Input/Output 1 or Use Link Loss Indicator (EM1 Kit Only)

The lost link indicator option is only available with the EM1 kit. When DIP switch 4 is OFF (default position), the link loss

error indicator uses output 1 and input 1 is not available. When DIP switch 4 is ON, input 1 is mapped to output 1. For the

ED1 kit, this DIP switch is ignored.

DIP Switch

Use Input/Output 1 or Use Link Loss Indicator

OFF *

Link Loss Error Indicator in Output 1 (Input 1 is unavailable)

Input 1 mapped to Output 1

2.1.2 Link Loss Timeout

The link loss timeout is the length of elapsed time during which there has been no communication between the Gateway

and Node. By default, if there has been no communication between the Gateway and Node for four seconds, the radio link

has failed.

DIP Switch

Link Loss Timeout

OFF *

4 seconds

1 second

2.2 Wiring Your Sure Cross

Device

Use the following wiring diagrams to first wire the sensors and then apply power to the Sure Cross devices.

2.2.1 I/O Mapping

All DX70 pairs ship from Banner Engineering with the I/O mapped.

2.2.1 DX70...EM1 Kits

Using PNP Inputs

Using NPN Inputs

PWR

GND
AO2

AO1
DO4

DO3
DO2

DO1

PWR

GND
AI2

AI1
DI4

DI3
DI2

DI1

−

Load

PWR

GND
AO2

AO1
DO4

DO3
DO2

DO1

PWR

GND
AI2

AI1
DI4

DI3
DI2

DI1

−

Load

Sure Cross

DX70 Wireless Point-to-Point Kits

www.bannerengineering.com - Tel: 763.544.3164

Содержание Sure Cross DX70




































Результаты поиска

Содержание Sure Cross DX70

Отзывы:

Бренды по названию

Популярные бренды

Banner Sure Cross DX70, Инструкция по эксплуатации

Результаты поиска

Содержание Sure Cross DX70

Отзывы:

Бренды по названию

Популярные бренды