Repairs
Contact Banner Engineering for troubleshooting of this device.
Do not attempt any repairs to this Banner device; it contains no
field-replaceable parts or components.
If the device, device part, or device component is determined to be defective by a Banner
Applications Engineer, they will advise you of Banner's RMA (Return Merchandise Authorization) procedure.
Important:
If instructed to return the device, pack it with care. Damage that occurs in return shipping is not
covered by warranty.
Specifications
Contact Rating
3 A at 240 V ac maximum, 2.5 kV maximum transient tolerance (U
imp
)
European Rating
Rated supply voltage 240 V (U
e
)
Utilization categories: AC15 U
e
/I
e
240 V/3 A
U
i
= 250 V ac, I
the
= 10 A
Rated conditional short-circuit current: 1000 A
Electrical Protection Class
II, protective insulation
Contact Function
Slow make and break contacts, 2 N.C., 2 N.O. (Zb)
Direct Opening Operation acc. IEC/EN60947-5-1 Annex K
Contact Material
Silver-nickel alloy
Latching Device
According to DIN EN 60947-5-5, IEC 60947-5-5, ISO 13850 (Compliant with
ANSI B11.19)
Switching Frequency
20 operations per minute (maximum)
Wire Rope Diameter
2 mm to 5 mm (3 mm is recommended; see
on p. 10)
Maximum Rope Pull Length
RP-LS42F-25xx: 25 m (82.0 ft); Force: 100 N
RP-LS42F-38xx: 38 m (124.7 ft); Force: 175 N
RP-LS42F-75xx: 75 m (246.1 ft); Force: 300 N
Short Circuit Protection
6 A Slow Blow (Type gG). Recommend external fusing or overload
protection.
B10d
1 x 10
5
cycles at DC-13; 24 V; I
e2
= 0.1 A
Mechanical Life
1 x 10
5
switching cycles (maximum) according to IEC 60947-5-5
Wire Connections
8 x cage clamp terminals
Conductor cross-section: 0.25 mm
2
to 1.5 mm
2
(16 AWG) solid or stranded
with ferrules
Cable Entry
M20 x 1.5 threaded entrance (x3)
Adapter supplied to convert M20 x 1.5 to ½ in - 14 NPT threaded entrance
Construction
Housing and cover: Polyamide PA 6 GV (UL94-V0)
Actuator: Zinc die-cast / steel
Environmental Rating
IP67 according to IEC/EN 60529
NEMA 4X (indoor use only)
The degree of protection specified applies solely to a property closed cover
and the use of an equivalent cable gland with adequate cable or conduit.
Operating Conditions
Temperature: –25 °C to +70 °C (–13 °F to +158 °F)
Mounting
4 x M5 (#10) screws (on flat and stiff surface) Maximum torque = 2 Nm
Weight
RP-LS42F-xxL: approximately 0.48 kg (1.05 lbs)
RP-LS42F-xxLF: approximately 0.69 kg (1.43 lbs)
Application Notes
Failure to follow the installation guidelines and procedures can result in the
ineffective or non-operation of the rope pull switch system that could create
an unsafe condition.
Standards
VDE 0660 T100, DIN EN 60947-1, IEC 60947-1
VDE 0660 T200, DIN EN 60947-5-1, IEC 60947-5-1
VDE 0660 T210, DIN EN 60947-5-5, IEC 60947-5-5
ISO 13850 (Compliant with ANSI B11.19 and NFPA 79)
EU-Conformity
According to directive 2006/42/EC (Machinery Directive)
Approvals
DGUV,
C
CSA
US
A300 (same polarity only)
Certifications
Rope Pull Emergency Stop Switches
8
www.bannerengineering.com - Tel: + 1 888 373 6767
P/N 67709 Rev. C
