manualshive.com logo in svg

Banner Q5XKLAF2000-Q8, Инструкция по эксплуатации

Поделиться
Скачать
Banner Q5XKLAF2000-Q8 Скачать руководство пользователя страница 31

Required Overcurrent Protection

WARNING: Electrical connections must be

made by qualified personnel in accordance

with local and national electrical codes and

regulations.

Overcurrent protection is required to be provided by end product

application per the supplied table.

Overcurrent protection may be provided with external fusing or via

Current Limiting, Class 2 Power Supply.

Supply wiring leads < 24 AWG shall not be spliced.

For additional product support, go to 

www.bannerengineering.com

.

Supply Wiring (AWG)

Required Overcurrent Protection (Amps)

20

5.0

22

3.0

24

2.0

26

1.0

28

0.8

30

0.5

Shock

MIL-STD-202G, Method 213B, Condition I (100G 6x along X, Y and Z

axes, 18 shocks), with sensor operating

Operating Conditions

–10 °C to +50 °C (+14 °F to +122 °F)

35% to 95% relative humidity

Storage Temperature

–25 °C to +70 °C (–13 °F to +158 °F)

Certifications

Industrial
Control
Equipment

3TJJ

Class 2 power
UL Environmental Rating: Type 1

Excess Gain

Excess Gain Using a 90% White Card 

2

Response Speed (ms)

at 100 mm

at 500 mm

at 1000 mm

at 2000 mm

3

150

50

15

4

5

150

50

15

4

15

725 (225)

250 (75)

70 (25)

15 (6)

25

1250 (800)

450 (250)

125 (70)

30 (15)

50

2500 (1250)

900 (450)

250 (125)

60 (30)

2

Standard excess gain available in 15, 25, and 50 ms response speeds; standard excess gain provides increase noise immunity.

 

 

Q5X Laser Triangulation Sensor with Background Suppression

 

www.bannerengineering.com - Tel: +1.763.544.3164

31

Содержание Q5XKLAF2000-Q8













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды