banks six-gun Скачать руководство пользователя страница 8

Страница: 8 / 41

96808 v.14 .0

If Six-Gun has been previously

installed, skip to Section 2.

Disconnect the battery ground

cables from each of the batteries.

Secure the cables so that they do not

come in contact with the battery posts

during the installation.

Remove the (+) battery cable from

the driver side battery.

Remove the driver side plastic

battery cover, as shown in

Figure 2

This is accomplished by depressing a

tab at the front and rear of the cover.

Be careful not to damage the cover, as

it will be re-installed.

Remove the driver side battery hold

down clamp (8mm socket). Remove

the driver side battery.

WARNING: When lifting a battery,

excessive pressure on the end

walls could cause acid to spew

through the vent caps, resulting in

personal injury. Lift with a battery

carrier or with hands on opposite

corners. Failure to follow these

instructions may result in personal

injury.

Section 1

INSTALLATION OF WIRING HARNESS & CONNECTIONS FOR SIx-GUN/

ECONOMIND DIESEL TUNER

Banks iQ System

.....................61152

Banks Monster

Exhaust:

‘03 F-250/350 Pickup

Ext cab, short bed .......................48764
‘04-07 F-250/350 Pickup

Ext cab, short bed .......................48784
‘03 F-250/350 Pickup

Ext cab, long bed ........................48766
‘04-07 F-250/350 Pickup

Ext cab, long bed ........................48786
‘03 F-250/350 Pickup

crew cab, short bed ...................48765
‘04-07 F-250/350 Pickup

crew cab, short bed ...................48785
‘03 F-250/350 Pickup

crew cab, long bed .....................48767
‘04-07 F-250/350 Pickup

crew cab, long bed ....................48787
‘03 Excursion ...............................48768
‘04-07 Excursion .........................48788

Additional Equipment:

Technicooler

(‘03-04) .....................25974

Technicooler

(‘05-07) .....................25975

Gauge Assembly,

Boost and Pyro ...........................64507

Thermocouple ............................63055

Содержание six-gun










































Результаты поиска

Содержание six-gun

Отзывы:

Бренды по названию

Популярные бренды

banks six-gun, Руководство пользователя

Результаты поиска

Содержание six-gun

Отзывы:

Бренды по названию

Популярные бренды