banks six-gun Скачать руководство пользователя страница 22

Страница: 22 / 41

96808 v.14 .0

Figure 19

Remove column panel covers

16.

Locate the Brake Position

Switch intercept connectors on the

Banks Brake Wire Harness. connect

the female connector on the Brake

Position Switch intercept connectors

to the factory black brake position

switch connector. connect the male

connector on the Brake Position Switch

intercept connectors to the factory

female brake position connector that

was disconnected.

17.

From under the steering column,

remove the three (3) screws that hold

the steering column panel covers in

place. See

Figure 19

18.

Using a standard screw driver

remove the plastic ignition key guide.

See

Figure 20

19.

Move the steering column down

to the lowest possible position to aid

in removal of the top steering column

panel. Remove the top steering column

panel.

CAUTION: Be careful when

removing the top steering column

panel or damage may result.

20.

Locate the tow haul connector

under the main wire harness towards

the top rear of the steering column.

See

Figure 21

21.

Disconnect the tow haul

connector.

22.

Locate the tow haul intercept

connector on the Banks Brake Wire

harness. Route the Tow Haul intercept

connectors under the dash towards

the front of the vehicle and up to the

top of the steering column following

the factory harness to the factory

tow haul connector. Make sure the

connectors and wires are free of

rotation from the steering column.

connect the female connector on

the Tow Haul intercept connectors to

the factory male tow haul connector.

connect the male connector on the

Tow Haul intercept connectors to the

factory female tow haul connector.

Secure the connectors and wires with

supplied cable ties.

Содержание six-gun










































Результаты поиска

Содержание six-gun

Отзывы:

Бренды по названию

Популярные бренды

banks six-gun, Руководство пользователя

Результаты поиска

Содержание six-gun

Отзывы:

Бренды по названию

Популярные бренды