![background image](http://html1.mh-extra.com/html/bang-and-olufsen/beosound-9000-mkiii/beosound-9000-mkiii_service-manual_3750686087.webp)
5.61 Error tree
Error tree 5.61
5.61
Reading guide
The error tree shown below is intended
as an aid in connection with servicing
BeoSound 9000, because the product
has a number of functions that are
dependent on each other.
The error tree is a guideline, and it
is based on troubleshooting procedures
at module level. The modules which
are listed as defective are the modules
which contain the faulty function. Since
the signals in BeoSound 9000 are often
Connect PL speakers. (Or
connect pin 2 & 4 in the
PL plug). Connect to mains.
Activate mains switch
The sledge must be at CD 1
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
Stand by LED lit?
START
Push "RADIO",
radio and display OK?
The CD Mechanism must
be set in position CD 1
Choose CD
Is the CD clamped?
(wait 30 sec)
Remove 34P10. Apply
9V to 34P10 pin 12,13
Audible clamping?
Push RADIO.
Supply for PCB01 OK?
Signal on 32P26, pin 1
& 2 OK? (digital signal)
Push "CD",
CD OK?
Does CD rotate,
but no sound?
Is there 9.5V AC
at the output of
90T1?
F1+F2 OK ?
Else remove 34P9.
Is the stby LED lit?
Check PCB4, 5
and 90T1
PCB35
(MOTOR CONTROL)
defective
PCB34
(POWER SWITCH.)
defective
PCB22
(CLAMPER POS.)
defective
PCB35
(MOTOR CONT.)
defective
PCB41 (CD)
defective
PCB01 (FM/AM)
defective
PCB32
(IN/OUTPUT SELECT)
defective
Clamper motor
or connection to
motor defective
Clamper pos.
inputs on 35IC2 OK?
Remove 34P2.
Light in stand by LED?
Remove 34P13.
Light in stand by LED?
Remove 34P14.
Light in stand by LED?
PCB32
(IN/OUTPUT SELECT)
defective
PCB13
(SEC. KEYBOARD)
defective
PCB14
(IR RECEIVER)
defective
PCB34
(POWER SUPPLY)
defective
Is basis high on
34TR43 when
choosing a source?
Check for
bus ERRORS
(TESTMODE 27)
+12V on 34P2 pin 4
and -12V on 34P2
pin 6, OK when
choosing a source?
Remove 34P2
+12V and -12V, OK
when choosing
a source?
PCB34
(POWER SUPPLY)
defective
34F2 OK?
PCB34
(POWER SUPPLY)
defective
PCB32
(IN/OUTPUT SELECT)
defective
Remove 34P6
+9VCD, OK
when choosing CD?
+9VCD on 34P6
pin 8, OK
when choosing CD?
PCB34
(POWER SUPPLY)
defective
PCB41 (CD)
defective
Go to next page
Is the glass door
able to open
and close?
Remove 37P76.
Apply 12V to lid motor.
Does it move?
Motor/Gearbox
unit defective
PCB35
(MOTOR CONTROL)
defective
looped through other modules, the
signal paths to the modules also have
to be checked.
NOTE:
The glass lid must either be on, or the hinge for
the lid must be in the open position.
In a fault situation the sledge may be unable to
move to its end stop (CD 1 position).
End stop detection is important for the
microprocessor when powering up the product.
Therefore the sledge should manually be
brought to the end stop position (the sledge is
released in TEST MODE 72).
Consejos orientativos
El árbol de localización de fallos
aparece en el diagrama adjunto se ha
de interpretar como ayuda para
trabajos de servicio en el sistema
BeoSound 9000, ya que el producto
tiene varias funciones que dependen
mutuamente una de otra.
El árbol de localización de fallos ha de
servir de pauta y está basado en
procedimientos de localización de fallos
a nivel de módulo. Los módulos que
Guida alla lettura
Il diagramma errori illustrato di seguito
costituisce un ausilio nelle operazioni di
assistenza su BeoSound 9000, poiché
l’apparecchio presenta molte funzioni
interdipendenti.
Il diagramma errori rappresenta una
guida e si basa sulle procedure della
ricerca guasti a livello di moduli. I
moduli elencati come difettosi sono i
moduli che contengono le funzioni
errate. Poiché i segnali in BeoSound
9000 spesso sono collegati ad anello
mediante altri moduli, occorre
controllare anche i percorsi dei segnali
per i moduli.
NOTA:
Il coperchio di vetro deve essere aperto oppure
la cerniera del coperchio deve essere in
posizione di apertura. In una situazione di
errore, è possibile che la slitta non sia in grado
di spostarsi verso l’arresto fi ne (posizione CD 1).
La rivelazione dell’arresto fi ne è importante per
il microprocessore durante l’accensione
dell’apparecchio.
Quindi la slitta deve essere portata
manualmente nella posizione di arresto fi ne (la
slitta è rilasciata in TEST MODE 72).
aparecen como defectuosos son
módulos que contienen la función
averiada. Dado que las señales del
sistema BeoSound 9000, con
frecuencia, está interconectadas a
través de otros módulos, también
deben verifi carse las trayectorias de
señal a los módulos.
NOTA: La tapa de vidrio debe estar colocada o
la bisagra de la tapa debe estar abierta.
En una situación de avería, el carro
transportador tal vez no pueda desplazarse a su
tope fi nal (posición de parada fi nal CD 1).
La detección de parada fi nal es importante para
el microprocesador a la hora de poner en
marcha el producto.
Por consiguiente, el carro transportador debe
colocarse manualmente en la posición de
parada fi nal (el carro transportador se libera en
el MODO DE PRUEBA 72).
Содержание BeoSound 9000 MKIII
