background image

7

Smart Pro, Smart & Secure

 installation instructions

6. Fit the Opener

6.1Secure C-Rail to Opener:

a. Remove the Opener from the box, taking care of antenna (if fitted).

b. Remove the track and hardware kit from the rail box.

c. Locate and insert the shaft of drive unit 

1

 into the C-Rail’s 

8

 sprocket.

d. Fix the two track brackets 

7a

 with four (4) M4 x 8 screws 

7k

 supplied in accessory pack. 

e. Place drive unit back in packing box for protection.

Locate shaft into 

the sprocket

8

1

WARNING!

DO NOT use tek screws 
to affix rail. Only use 
the screws provided, 
and fix these into the 
threaded holes in the 
chassis.

7. Bracket Position

7.1Wall Bracket Position:

a. Determine the centre of the door and mark this point with a line on the 

wall above.

b. Raise the door and find the highest point of travel of the first (top) door 

panel.

60mm

Level

WARNING! The Opener must be securely fastened to structural 

supports, otherwise opener failure may ensue causing serious 

personal injury and / or property damage.

DO NOT DO IT YOURSELF: If sufficient structural support can 

not be found, contact a door profressional for installation.

DIY

c. Using  step ladder and a level, transfer this height to the wall above the 

door and mark a line 60mm above it, across the centre line.

7.2 Mounting the Wall Bracket:

a. Draw two lines extending 21.5mm from each side of the centre point.

b. Centre the wall bracket 

7e

 over the intersection of these two lines. 

Mark centres for at least two holes and ensure it is into a solid mounting 

point.

c. Drill holes in the wall with an appropriate bit.

d. Secure to the wall using:

i.  IF CONCRETE OR BRICK: 

8mm (5/6”) loxins/dynabolts.

ii.  IF TIMBER: 

wood screw #20 or similar (min. 50mm).

7.3 Attach the Track to the Wall Bracket

a. Leave the drive unit in its packing box on the floor for protection and 

lift the other end of the C-Rail.

b. Attach the pre-assembled track 

8

  to the wall bracket 

7e

 with the  

90mm long pin 

7h

 

and secure with the supplied pin snap 

7f

.

8

7a

7k

7e

7e

7h

7f

Содержание Smart Pro SDO-9V3






























Отзывы: