background image

Troubleshooting

Suspected malfunctions are often due to causes that the users can fix themselves. 

Therefore check the product using this section. In most cases the problem can be 

solved quickly.

WARNING! 

Only perform the steps described within these instructions! 

All further inspection, maintenance and repair work must be performed 

by an authorised service centre or a similarly qualified specialist if you 

cannot solve the problem yourself!

Problem

Possible cause

Solution

1.  Product does 

not start

1.1 Not connected to power 

supply 

1.2 Power cord or plug is 

defective

1.1 Connect to power supply

1.2 Check by a specialist 

electrician

2.  Product does 

not reach full 

power

2.1 Extension cord not 

suitable for operation 

with this product

2.2 Power source (e.g. 

generator) has too low 

voltage

2.3 Air vents are blocked

2.1 Use a proper extension cord

2.2 Connect to another power 

source

2.3 Clean the air vents

3. Unsatisfactory 

result

3.1 Drill bit is dull/damaged

3.2 Drill bit not suitable for 

work piece material

3.1 Replace with new one

3.2 Use proper drill bit

4.  Excessive 

vibration or 

noise

4.1 Drill bit is dull/damaged 4.1 Replace with a new one

Recycling and disposal

Waste electrical products should not be disposed of with household 

waste. Please recycle where facilities exist. Check with your local 

authority or local store for recycling advice.

24

Содержание PRH850C




























Отзывы: