Bandit
41
Copyright 6/18
MODEL 2590
MAINTENANCE
1. Check anvil clearance, tightness, and wear:
Measure the anvil clearance. The clearance should
be .120” (3.0 mm) from highest knife. Check the
anvil hardware, make sure the bolts are at the proper
torque. The anvil is a normal wear item, if it is worn
you can rotate it to a new working edge. Refer to
pages 56 - 57 for the exact checking of anvil
clearance procedure.
2. Check alternator and fan belts on engine:
Inspect belt condition and replace as needed.
As applicable adjust and maintain per the engine
manufacturer’s manual.
3. Check wheel lug nuts (if equipped):
Keep lug nuts tight, retorque, replace if needed.
4. Check fluid level in pump bearing block(s):
Keep the fluid level in the pump bearing block(s) full,
use an 80W/90 type gear lube. Requires a minimum
of 2.2 oz (65 ml) and a maximum of 4.4 oz (130 ml).
5. Lubricate all steel friction areas:
Lubricate all steel friction areas including, but not
limited to pivoting, hinged, sliding, rotating areas
on the machine (i.e. conveyor chain, cabinet doors,
discharge, discharge flipper, engine adjusters, etc.)
6. Lube chain driven components:
Use a dry lube on any chain driven components:
chain driven feedwheels, etc.
WEEKLY MAINTENANCE
1. Grease drum head bearings:
Grease with 16 pumps, every 120 hours or once
a month with a specific synthetic type grease. Use
Mobil 1 Universal Synthetic grease, Mobil SHC 220
Synthetic grease, Mobil AW2 Synthetic grease, or
Amsoil Multi-Purpose Grease NLGI#2.
2. Check towing hitch (if equipped):
Check for excessive damage or wear. Replace if
needed. Keep pintle ring or 5th wheel greased to
reduce wear.
3. Check discharge and infeed hopper wear:
Check for wear on discharge, infeed hopper, and
discharge direction adjustor; build up, repair or
replace as needed.
4. Inspect feedwheel motor connections,
sprockets, and bushings:
Check and maintain correct torque, on feedwheel
motor connections, sprockets, and bushings.
5. Check feedwheel teeth for sharpness:
Replace if needed.
6. Check infeed conveyor chain:
Check the tracking and tightness of the infeed
conveyor chain. Make sure the chain is running true.
Adjust as needed.
7. Check chipper bearings and chipper sheave:
Check, retighten all bearing bolts, bearing lock
collars, and also belt sheave bushings to correct
torques.
8. Check hydraulic pumps, motors, and gear
boxes:
Check tightness and connections of all hydraulic
pumps, hydraulic motors, and gear boxes. Tighten
if needed.
9. Check hydraulic function pressures:
Check, reset and maintain all hydraulic function
pressure settings to a maximum of the specified
PSI (bar). This will give you the best performance
from the hydraulic system.
10. Check wheel bearings (if equipped):
Check and grease or oil wheel bearings per axle
manufacturer’s instructions.
11. Check and adjust brakes (if equipped):
Check and adjust brakes as needed per axle MFG.
manual.
MONTHLY MAINTENANCE
1. Hydraulic oil filter(s):
Must be replaced after FIRST 10 HOURS OF
OPERATION, USE A 10 MICRON FILTER. After first
change replace oil filter every 3 months or 400 hours.
3 MONTH MAINTENANCE
2. High pressure oil filters:
Must be replaced every 3 months or 400 hours or if
the restriction gauge shows that it needs changed,
USE A 10 MICRON FILTER.
Содержание 2590
