Bandit
11
Copyright 6/18
MODEL 2590
Before you begin to transport your trailerized
machine follow all of the transportation procedures
on pages 34 - 36. Make sure that the tongue
has been raised to the proper height and attach
the machine securely to the towing vehicle. Once
secured to vehicle, locate tongue jack and secure it
in the transport position. Always hook safety chains
to vehicle by crossing them under the tongue allowing
enough slack to avoid binding or dragging the ground
when making turns. Check brakes and highway lights
make sure that they are all operating properly. Check
that the plug terminal functions match the towing
vehicle for proper operation. Make sure that the
discharge chute is in the transport position pointed
over the tongue of machine and the transport bolt is
securely in its place. Be sure to check tire pressure
before you begin to transport the machine. Close the
folding pan, if equipped for the infeed hopper and
make sure spring latches are locked into place. If
machine is equipped with a vise, make sure to secure
in place and clamp jaws closed. Close and secure
any of the following, if equipped: tool box, battery box,
engine cowl doors and side panels, radiator debris
screens, inspection doors, cabinet doors, housing
covers, tank caps and covers, etc.
WARNING
!
SAFETY PROCEDURES
SAFETY PROCEDURES
Tongue jacks or optional rear stabilizers, whether
hydraulic or manually operated are designed to
stabilize the machine. The tongue jack or rear
stabilizers are not designed to hold the machine
off the ground at any time. Install secure blocking
and / or chocking as needed. Before transporting
the machine, ensure the tongue jack and rear
stabilizers are fully retracted and secured to the
transport position.
Check laws and regulations. Know and obey all
federal, state, and local laws and regulations that
apply to your work situation and the transportation
of a machine this size.
NOTICE
WARNING
!
Always block the tires and the machine tongue
whenever the machine is unhooked for operation.
DO NOT rely on the hydraulic stabilizers. With the
bouncing and rocking, the stabilizer cylinders may
have a tendency to leak off allowing the machine
to drop down slowly. Do not depend on them for
stability. Install secure blocking as needed.
DANGER
!
CLEAN MACHINE OF ALL DEBRIS!
DO NOT
leave this machine unattended until all potential fi re
debris is removed, no fi re or smoldering exists, and
hot spots are cold. The engine creates many hot
spots including: exhaust manifold, exhaust, turbo
(if equipped), etc. Remove all flammable debris
such as wood, chips, leaves, oils, fuels, etc. from
engine exhaust, engine turbo (if equipped), beside,
around, and under engine, around and under tanks,
inside belt shields and guards, inside battery and tool
boxes, inside cabinets (if equipped), and anywhere
materials collect. ALWAYS keep several type A:B:C fi re
extinguishers operational and on the job at all times.
WARNING
!
Expensive damage to the Bandit will occur if
proper preparation is not taken before welding on
the machine. Be sure to disconnect both battery
cables and the engine ECM (engine control module)
before welding. Follow the specifi c Engine MFG.
instructions for proper welding and grounding
procedures, before attempting to weld on the
machine. If welding on the machine, do not ground
the welder through the machine bearings, ground
near work to be performed.
NOTICE
Operation of this equipment may create sparks
that can start fi res around dry vegetation. A spark
arrester may be required. The operator should con-
tact local fi re agencies for laws or regulations relating
to fi re prevention requirements.
WARNING
!
Refer to the Material Safety Data Sheet (MSDS)
for information pertaining to the knife babbitt material
including the health hazard information, fi rst aid
procedures, special handling procedures, disposal
procedures, etc. If needed, contact your nearest
dealer or Bandit Industries for the knife babbitt
MSDS.
WARNING
!
DANGER
!
DO NOT operate this chipper or loader arm when
anyone is performing any type of maintenance
to the machine. Before attempting any type
of maintenance disengage clutch, wait for the
disc/drum to come to a complete stop, turn off
engine, remove the ignition key, make sure the
ignition key is in your possession, install the
disc/drum lock pin, disconnect the battery, and the
loader, if equipped, is positioned on the ground.
Failure to do this could result in serious injury or death.
DANGER
!
Do not touch hot machine surfaces. The machine
surfaces may be hot due to the machine operating
recently or the machine setting in the sunlight.
Before performing maintenance on the machine re-
move all debris, oil, grease, water, snow, ice, etc.
from all machine surfaces.
WARNING
!
Содержание 2590
