baltur GI 350 DSPN Скачать руководство пользователя страница 6

Страница: 6 / 104

2 / 28

0006081143_200905

WARNING NOTES FOR THE USER HOW TO USE THE

BURNER SAFELY

FOREWORD

These warning notes are aimed at ensuring the safe use of the components

of heating systems for civil use and the production of hot water. They

indicate how to act to avoid the essential safety of the components being

compromised by incorrect or erroneous installation and by improper or

unreasonable use. The warning notes provided in this guide also seek

to make the consumer more aware of safety problems in general, using

necessarily technical but easily understood language. The manufacturer

is not liable contractually or extra contractually for any damage caused by

errors in installation and in use, or where there has been any failure to follow

the manufacturer’s instructions.

GENERAL WARNING NOTES

• The instruction booklet is an integral and essential part of the product and

must be given to the user. Carefully read the warnings in the booklet as

they contain important information regarding safe installation, use and

maintenance. Keep the booklet to hand for consultation when needed.

• Equipment must be installed in accordance with current regulations, with

the manufacturer’s instructions and by qualified technicians. By the term

‘qualified technicians’ is meant persons that are competent in the field

of heating components for civil use and for the production of hot water

and, in particular, assistance centres authorised by the manufacturer.

Incorrect installation may cause damage or injury to persons, animals

or things. The manufacturer will not in such cases be liable.

• After removing all the packaging make sure the contents are complete and

intact. If in doubt do not use the equipment and return it to the supplier.

The packaging materials (wooden crates, nails, staples, plastic bags,

expanded polystyrene, etc.) must not be left within reach of children

as they may be dangerous to them. They should also be collected and

disposed on in suitably prepared places so that they do no pollute the

environment.

• Before carrying out any cleaning or maintenance, switch off the equipment

at the mains supply, using the system’s switch or shut-off systems.

• If there is any fault or if the equipment is not working properly, de-activate

the equipment and do not attempt to repair it or tamper with it directly. In

such case get in touch with only qualified technicians. Any product repairs

must only be carried out by BALTUR authorised assistance centres using

only original spare parts. Failure to act as above may jeopardise the

safety of the equipment. To ensure the efficiency and correct working of

the equipment, it is essential to have periodic maintenance carried out

by qualified technicians following the manufacturer’s instructions.

• If the equipment is sold or transferred to another owner or if the owner

moves and leaves the equipment, make sure that the booklet always

goes with the equipment so it can be consulted by the new owner and/

or installer.

• For all equipment with optionals or kits (including electrical), only original

accessories must be used.

BURNERS

• This equipment must be used only for its expressly stated use: applied to

boilers, hot air boilers, ovens or other similar equipment and not exposed

to atmospheric agents. Any other use must be regarded as improper use

and hence dangerous.

• The burner must be installed in a suitable room that has ventilation in

accordance with current regulations and in any case sufficient to ensure

correct combustion

• Do not obstruct or reduce the size of the burner’ air intake grills or the

ventilation openings for the room where a burner or a boiler is installed

or dangerous mixtures of toxic and explosive gases may form.

• Before connecting the burner check that the details on the plate correspond

to those of the utility supplies (electricity, gas, light oil or other fuel).

• Do not touch hot parts of the burner. These, normally in the areas near

to the flame and any fuel pre-heating system, become hot when the

equipment is working and stay hot for some time after the burner has

stopped.

• If it is decided not to use the burner any more, the following actions must

be performed by qualified technicians:

a) Switch off the electrical supply by disconnecting the power cable from

the master switch.

b) Cut off the fuel supply using the shut-off valve and remove the control

wheels from their position.

c) Render harmless any potentially dangerous parts.
Special warning notes
• Check that the person who carried out the installation of the burner fixed

it securely to the heat generator so that the flame is generated inside the

combustion chamber of the generator itself.

• Before starting up the burner, and at least once a year, have qualified

technicians perform the following operations:

a) Set the burner fuel capacity to the power required by the heat

generator.

b) Adjust the combustion air flow to obtain combustion yield of at least

the minimum set by current regulations.

c) Carry out a check on combustion to ensure the production of noxious

or polluting unburnt gases does not exceed limits permitted by current

regulations.

d) Check the adjustment and safety devices are working properly.
e) Check the efficiency of the combustion products exhaust duct.
f) Check at the end of the adjustments that all the adjustment devices

mechanical securing systems are properly tightened.

g) Make sure that the use and maintenance manual for the burner is

in the boiler room.

• If the burner repeatedly stops in lock-out, do not keep trying to manually

reset but call a qualified technicians to sort out the problem.

• The running and maintenance of the equipment must only be carried out

by qualified technicians, in compliance with current regulations.