Balluff BSP-B-004-S1A Series Скачать руководство пользователя страница 9

www.balluff.com

1

English

Installation

Caution! 

Do not allow the pressure transmitter to be 

exposed to high temperatures or rapid 

increases in pressure that extend beyond 

specific limits (see Technical Data for limit 

values).

 

– Always depressurize and disconnect pressure trans-

mitters from the power supply before installing! 

 

– Observe the following when installing outdoors or in a 

damp environment:
Select a installation location that allows splash and 
condensation water to drain away. Fluids must not be 
allowed to accumulate on sealing surfaces!
Connect the device to the power supply immediately 
after installation to prevent moisture from entering the 
connector. Otherwise fit a suitable protective cap to 
prevent the ingress of moisture. The degree of protec-
tion specified on the data sheet only applies if the 
device is connected!

If there is a risk of damage from lightning or excess 
voltage, mount overvoltage protection between the 
power supply unit or switching cabinet and device. 

 

– On hydraulic systems, position the device so that the 

pressure connection faces upwards (venting). 

 

– If the device is installed on a steam pipeline, provide a 

cooling section. 

 

– Mount the device in a location protected from direct 

sunlight. Sunlight can damage or affect the functional 
capability of the device. 

 

– When installing devices with a gauge reference in the 

housing (small hole in the transmitter housing), make 
sure that the gauge reference required for the mea-
surement is protected against dirt and moisture. If the 
device is exposed to fluids, the gauge reference blocks 
the air pressure compensator. Accurate measurements 
are not possible when this happens. and the device 
may be damaged. 

 

– No mechanical tension should be placed on the pres-

sure connection during installation as this may shift the 
characteristic curve. This applies in particular to 
extremely small pressure ranges and devices with a 
plastic pressure connection.

EU Directive 2004/108/EC (EMC Directive) and EMC Law

Generic Standards: EN 61000-6-4 (Emissions), EN 61000-6-2 (Interference Immunity)

Emissions testing: Radio interference emissions EN 55011 Group 1, Class A and B

Intended use

The pressure transmitter has been developed to monitor 
the pressure of gases or fluids compatible with stainless 
steel, ceramics and fluoroelastomers. Pressure transmit-
ters are suited to different types of application depending 
on the device and mechanical connection. 

The pressure transmitter is installed in a machine or inte-
grated into a system. Flawless function in accordance with 
the specifications in the technical data is ensured only 
when using original BALLUFF accessories, and use of any 
other components will void the warranty. 

Modifications to the transmitter or non-approved use are 
not permitted and will result in loss of warranty and void 
any liability claims against the manufacturer.

Safety instructions

Before commissioning, read the user's guide 

carefully!

These sensors must not be used in applications 

in which the safety of persons is dependent on 

the function of the device (not a safety compo-

nent acc. to EU Machinery Directive).

Installation and startup

 are to be performed only by 

trained specialists. 

The 

operator

 is responsible for ensuring that local safety 

regulations are observed.
In particular, the operator must take measures to ensure 
that a defect in the pressure detection system will not 
result in hazards to persons or equipment.
If defects or non-clearable faults in the sensor occur, take it 
out of service and secure against unauthorized use.

Downloading the user's guide

The user's guide can also be found on the Internet at 

www.balluff.com

.

Validity

This guide is valid for the following pressure transmitters:

 

– BSP-Bxxx-xx004-xxxS1A-xx

 

– BSP-Vxxx-xx004-xxxS1A-xx

Pressure Transmitters with IO-Link

BSP-Bxxx-xx004-xxxS1A-xx, BSP-Vxxx-xx004-xxxS1A-xx 

Содержание BSP-B-004-S1A Series









































Отзывы: