www.balluff.com
7
english
2.4
General safety notes
Installation
and
startup
may only be performed by
qualified personnel with basic electrical knowledge.
Qualified personnel
are persons whose technical
training, knowledge and experience as well as knowledge
of the relevant regulations allow them to assess the work
assigned to them, recognize possible hazards and take
appropriate safety measures.
The
operator
is responsible for ensuring that local safety
regulations are observed.
In particular, the operator must take steps to ensure that a
defect in the device will not result in hazards to persons or
equipment.
If defects and unresolvable faults occur in the device, take
it out of service and secure against unauthorized use.
When connecting the processor unit to an external
controller, observe proper selection and polarity of the
connection as well as the power supply.
The antennas of the identification system BIS U transmit
ultra-high frequency electromagnetic waves.
IEC 62369 stipulates that personnel must not remain within
close range of the UHF antenna for long periods (several
hours).
Any damage resulting from unauthorized tampering or
improper use shall void warranty and liability claims against
the manufacturer.
For operation within the European Union:
When selecting the installation position for the processor
unit, make sure that the minimum distance between the
UHF antenna and the workplace is 26 cm.
The radiated power must not exceed the maximum
permitted limit values:
– 1 watt
ERP
for antennas with an opening angle ≤ 180°
– 2 watt
ERP
for antennas with an opening angle ≤ 90°.
For operation in the USA and Canada:
When selecting the installation position for the processor
unit, make sure that the minimum distance between the
UHF antenna and the workplace is 50 cm.
The radiated power must not exceed the permissible limit
value of 4 watts
EIRP
.
See the “Basic UHF manual” for more
information on minimum/maximum distances
and antenna power.
2.5
Conformity
All product variants for hardware version 2.0 or
higher
2.5.1 BIS U-6026-034-104-06-ST35
The CE Mark verifies that our products meet the
requirements of the current EMC Directive.
More detailed information on the guidelines and
standards is included in the declaration of
conformity. The complete EU Declaration of
Conformity can be found in the internet at
www.balluff.com.
To view it, enter the order
code of your model into the search box.
2.5.2 BIS U-6026-034-114-06-ST35
FCC ID
– WJ9-RRU4ETGU6
– 2AGZY-BFIDU05 (for hardware version 2.0 or
higher)
This device complies with Section 15 of the FCC Rules.
The following two conditions apply to operation:
– this device may not cause interference
– this device must accept any interference, including
interference that may cause undesired operation of the
device
2
Safety (continued)
BIS U-6026-034-1_4-06-ST35
Processor unit
Содержание BIS U-6026-034-104-06-ST35
