background image

Document ref.: IBVCP issue 1

Page 1 of 22

Product Manual

IBVCP1

VIGIL AssureCare

Product Description

VIGIL AssureCare is a sophisticated emergency call-point system, which has been developed in accordance
with BS5839 part 9 and BS5588. The system is a fully monitored and battery-backed communication network,
and has capabilities to function as a Disabled Refuge System, Emergency Help Point System or a simple Call
Point System.

The system has two main components: the Main Control Panel and the Call Point Remote Units. The Main
Control Panel is available in eight options: 16, 32, 48, 64, 80, 96, 112 or 128 way. The panel is normally wall
mounted within a permanently manned main Control Room. There are two versions of Call Point Remote Units
available (red or in stainless steel), which are wall-mounted in areas of risk, such as stairwells, corridors and
‘gathering’ areas.

In an emergency situation, personnel can press the Call button on a Call Point Remote Unit to call and speak
with a Fire Officer or Building Manager. The Fire Officer or Building Manager uses a press to talk telephone
handset at their dedicated Control Panel(s) to control the half-duplex communication with Call Points on an
‘all-call’ or individual basis to relay instructions or to provide reassurance.

Slave Control Panels can be added to the system for control of local zones of Call Point Remote Units (e.g. in
a stairwell), and repeater units are available to extend the cabling distance between the Remote Units.

Manual Contents

Product Description

1

Manual Contents

1

CE Declaration

2

Safety and Precautions

2

Equipment Specifications

2

For the System Designer:

System Cabling Types & Distances And Installation Recommendations

3

For the Equipment Installer:

Equipment Installation

10

For the System Commissioner:

System Commissioning

13

How to Use the Zone Insert Labels

17

For the System Maintainer:

System Maintenance and Expansion

20

Control Panel Indicators and Controls

21

For the System User:

Operator’s Manual

supplied separately

Содержание VIGIL AssureCare




























Отзывы: