background image

1-2 Product Safety Information

MN2417

This symbol is shown throughout the manual to indicate a connection to ground reference point.

 

Symbols

Indicates a potentially hazardous situation which, if not avoided, could result in injury or death.
Indicates a potentially hazardous situation which, if not avoided, could result in injury or death.

Precaution Statements Used In This Manual

There are three classifications of precautionary statements used in this manual.  The most critical

is a 

WARNING

 statement, then the 

Caution

 statement and the least critical is the Note

statement.  The usage of each statement is as follows:

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in injury or

death.

Caution:

Indicates a potentially hazardous situation which, if not avoided, could result in damage to

property.

Note:

Additional information that is not critical to the installation or operation.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

 

  

This manual contains important instructions for the generator that

should be followed during installation, operation and maintenance of the generator.

For ease of reading, the Warning statements are divided into four categories: Operation, Burn, Installation,

and Maintenance.

Operation
WARNING: Never allow a person to ride in or on a trailer that is being towed.  All states prohibit

passengers in towed vehicles.  A person can fall off and be struck be another vehicle or run

over by the towed trailer.  Failure to observe this warning can result in death.

WARNING: Before using a tow vehicle with a trailer mounted generator, verify that the vehicle is designed

for the load.  Using a vehicle that is too small is very dangerous.  Be certain that it can handle

the M.G.T.W. (Maximum Gross Trailer Weight) and the tongue weight for safe towing and

braking.

WARNING: For a new trailer, the wheel lug nuts should be tightened to the proper torque specification

before use, after 25 miles of operation and every 100 miles of operation thereafter.  Failure to

check the lug nuts for proper tightness can result in an accident due to a wheel falling from

the trailer.

WARNING: Never operate a trailer or tow vehicle that has a loose, missing or broken lug nut.  The trailer

is designed for safe operation with all lug nuts installed and all at the proper torque rating.

Operating the trailer with one or more broken or missing lug nuts greatly increases the load

on the remaining nuts and can cause failure of the remaining nuts that can result in an

accident due to a wheel falling from the trailer.

WARNING: Never operate this generator in a manner other than as described in this manual.  Operation

in any manner not described in this manual should be considered unsafe and should not be

attempted.  Never start the engine unless you have first verified that the installation and

operation of the generator are as described in this manual.

WARNING: Be sure that you are completely familiar with the safe operation of this equipment.  This

equipment may be connected to other machines that have rotating parts or parts that are

controlled by this equipment.  Improper use can cause serious or fatal injury.

WARNING: Exhaust fumes/gases are extremely dangerous and can cause severe illness or death.  Never

breath exhaust fumes produced by a running engine.  Only run the engine outdoors where

ventilation is plentiful.  Exhaust gases contain carbon monoxide, a colorless, odorless and

extremely dangerous gas that can cause unconsciousness or death.  Symptoms of carbon

monoxide poisoning include: dizziness, nausea, headaches, sleepiness, vomiting or

incoherence.  If you or anyone else experiences these symptoms, get out into fresh air

immediately.  Stop the engine and do not restart the engine until it has been inspected and if

necessary repaired or reinstalled in a well ventilated area.

WARNING: When operating this generator remain alert at all times.  Never operate machinery when

physically or mentally fatigued, or while under the influence of alcohol, drugs or medication.

Continued on next page.

Содержание TS25



























































































Отзывы: