9
1
827710 AIR VALVE ASSEMBLY
1
1 1 1
2
826658 UPPER PUMP ROD
1
1 1 1
3
805723 CRIMP NUT
1
1 1 1
4
805756 WASHER
1
1 1 1
5
826052 ADAPTOR
1
1 1 1
6
826680 ROD
1
1 1 1
7
827414 LOWER PUMP ROD (ALUM)
1
1
827415 LOWER PUMP ROD (316SS)
1
1
8
820015 #120 O-RING (BUNA-N)
1
1
827441 #120 O-RING (VITON)
1
1
9
827416 PUMP ROD ADAPTOR (ALUM)
1
827417 PUMP ROD ADAPTOR (316SS)
1
10 827428 LOCK WASHER (18-8SS)
2 2
11 827429 NUT (18-8SS)
2 2
12 827418 CONNECTING ROD (STL)
1
827419 CONNECTING ROD (316SS)
1
13 827420 PISTON ADAPTOR (ALUM)
1
827421 PISTON ADAPTOR (316SS)
1
14 827168 "1"" BALL (DELRIN)
2
2 2 2
15 827422 FLUID PISTON (ALUM)
1
1
828988 FLUID PISTON (316SS)
1
1
16 816853 #223 O-RING (BUNA-N)
1
1
827065 #223 O-RING (VITON)
1
1
17 826660 CAP (ALUM)
1
1 1 1
18 828529 FLAT GASKET (NYLON)*
2
2 2 2
19 826663 SPRING*
1
1 1 1
20 826664 SPRING RETAINER
1
1 1 1
21 826665 "1/4-20 X 1/2"" SCREW"
1
1 1 1
22 827727 AIR PISTON TUBE (STL)
1
1 1 1
23 808439 SPRING*
1
1 1 1
24 807342 #222 O-RING (BUNA-N)*
1
1 1 1
25 827780 UPPER BODY (ALUM)
1
1 1 1
26 827767 MUFFLER SCREEN (BRASS)
2
2 2 2
27 827766 MUFFLER FOAM ***
2
2 2 2
28 827426 RETAINING RING
1
1 1 1
29 827425 BACKUP RING (BRASS)
1
1 1 1
30 826071 WIPER SEAL (BUNA-N)**
1
1
826072 WIPER SEAL (VITON)***
1
1
31 828365 LOWER BODY (ALUM)
1
1
828366 LOWER BODY (316SS)
1
1
32 829002 LOCK WASHER (STL)
4
4 4 4
33 829001 "1/4-20 x 3/4"" SCREW (STL)"
4
4 4 4
34 826678 # 33 O-RING (BUNA-N)**
1
1
826679 #132 O-RING (VITON)***
1
1
35 828361 PUMP TUBE (STL)
1
828363 PUMP TUBE (304SS)
1
828362 PUMP TUBE (STL)
1
828364 PUMP TUBE (304SS)
1
36 826678 #133 O-RING (BUNA-N)**
1
1
826679 #132 O-RING (VITON)***
1
1
37 826060 FOOTVALVE (STL)
1
1
829027 FOOTVALVE (316SS)
1
1
38 827427 RETAINING PIN (316SS)** ***
1
1 1 1
39 827062 #215 O-RING (BUNA-N)
1
827063 #215 O-RING (VITON)
1
!
Parts List
PUMP SERVICING
NOTE:
Air motor is lubricated with a life tested
synthetic grease (Balcrank P/N 826733) at
the factory. This grease coats all parts and
repels air line moisture to inhibit corrosion. It
is imperative that any grease removed during
routine maintenance be replaced. Contact your
local Balcrank Distributor, using the above part
number, for replacement grease.
NOTE:
The following steps and item numbers
pertain to the stub pumps. Except for a few fluid
section components (pump tube, pump rod, fluid
piston, etc.), stub and drum pumps are alike.
When repairing a drum pump, pay close attention
to different parts that may carry the same item
number as their stub counterparts, such as the
pump tube (35).
Repair Kits:
There are three kits available to
repair the stub and drum “Bobcat 130” pumps:
* 827711 (air piston parts for all pumps)
** 828069 (fluid seals for carbon steel pumps)
*** 828070 (fluid seals for stainless steel
pumps).
NOTE:
A complete list of materials for each repair
kit is on page 11 - Repair Kits
CAUTION:
Before servicing
reduce fluid supply pressure to zero.
Pressure Relief Procedure:
To reduce the risk of serious bodily injury,
including fluid injection or splashing into the
eyes and/or onto the skin, follow this procedure
below before maintaining and/or repairing the
pump, solenoid and/or impulse meter or any
part of your system.
1. Disconnect the air supply from the pump.
2. Open the dispensing valve into an approved
waste container to relieve pressure on the
system.
3. Leave any bleed-type drain valves open until
you are ready to use the system again.
ITEM PART
DESCRIPTION
11
10-001
1160-002
11
10-003
1160-003
