background image

Page 6

55370_97_A

Base Model VS503SZ-VS504SZ-VS514SZ

DIP Switches and Jumpers Definitions

DIP Switch Key

 

A1  Test Mode (normally OFF)

 A2+A10   

Control amp draw requirements (See Table 1)

 

A3  “ON” position: J17/26 pump enabled

 

  “OFF” position: J17/26 pump disabled

 

A4  Aux Freeze (must be OFF)

 

A5  When A9 is OFF. this switch is ignored and Pump 1 must be a two-speed pump.

 

  “ON” position: Two-speed pump 1

 

  “OFF” position: One-speed pump 1 (A9 must be On and a Circ Pump installed)

 

A6  “ON” position: 50Hz operation

 

  “OFF” position: 60Hz operation

 

A7  “ON” position: off-board equipment enabled (requires expander board to be installed)

 

  “OFF” position: off-board equipment disabled

 

A8  “ON” position: temperature is displayed in degrees Celsius

 

  “OFF” position: temperature is displayed in degrees Fahrenheit

 

A9  “ON” position: 24 Hour Circ Pump with 3ºF shut off, Ozone runs with Circ Pump

 

  “OFF” position: no Circ Pump, Ozone runs with Pump 1-low during filter cycles only

* Panel with button layout 

 is not compatible.

SSID 100 93 39-41

WARNING:

s

Setting DIP switches incorrectly may cause abnormal system behavior and/or damage to system components.

s

Refer to Switchbank illustration on Wiring Configuration page for correct settings for this system.

s

Contact Balboa if you require additional configuration pages added to this hot sheet.

Panel Button Positions

Aux Panel Information

Panel Button Assignments

1=Mode
2=Temp Up
3=Temp Down
4=Light

5=Pump 1
6=Pump 2 (when A3 is ON)
7=Exp Board (when A7 is ON)

Supports 2-button aux panel

VX20

When A3 is ON

Supports 4-button aux panel

VX40S

4

5

6

7

1

2

3

4

7

6

5

2

3

1

5

5

6

4

7

6

VX20

When A3 is OFF

5

7

Table 1 

# of Hi-Speed 

  

Pumps/Blower 

   

Before Heat Disabled

 A2 

A10 

 OFF 

OFF 

0

 ON 

OFF 

1

 OFF 

ON 

2

 ON 

ON 

3

Jumper Key 

J12 

 

Factory set.  DO NOT MOVE.

 

  Jumper must be on Pins 1 and 2 for VS51xZ/VS5xxSZ/VS5xxDZ software.

 

  Jumper must be on Pins 2 and 3 for VS50xZ software.

J43

    When jumper is placed on 2 pins during power-up, system will reset persistent memory.

 

  Leave on 1 pin only to enable persistent memory feature.

Содержание VS504SZ









Отзывы: