Baker SterilGARD III Advance Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 65

background image

Document: 333D012G

5-18-2007

- 9 -

Specifications

Weight

The weight of the SterilGARD

®

III Model SG403A / SG603A cabinet is 564 / 775 pounds [2509 / 3447 N] with a

shipping weight of 684 / 920 pounds [3042 / 4092 N]. With channel stand, the cabinet weight is 640 / 858 pounds
[2847 / 3816 N] with a shipping weight of 760 / 1003 pounds [3380 / 4461 N].

Electrical Specifications

All electrical wiring should comply with the National Electrical Code and any applicable
Local Electrical Codes at the site of installation.

A single 115V AC, 20A, 60 Hz, Single Phase dedicated circuit is required to power this unit. This circuit shall
provide the protective earth ground for the cabinet.

The cabinet is internally protected with a 250V, 20A Circuit breaker.

Cabinet Ratings:

115V AC, 60Hz, Single Phase

Typical current less outlets for SG403A

8.0 Amps

Typical current less outlets for SG603A

12.0 Amps

The unit is furnished with one 14' power cord with 20-amp plug, type NEMA 5-20P.

The power cord is the Main Disconnect device for the unit. The unit should be positioned
in a manner that allows easy access to the power cord connection to the electrical utility.

The cabinet is provided with Fluorescent lighting.

The cabinet is provided with two GFCI protected, 115V AC, Duplex outlets. The outlet(s) on this circuit are
protected by a self-resetting circuit breaker. For the SG403A the breaker allows 5A total on all outlets. For the
SG603A the breaker allows 3A total on all outlets.

The cabinet may be provided with an optional lift that requires 115V AC at 2 Amps intermittent duty. The lift duty
cycle is 1 minute on, 9 minutes off.

The cabinet incorporates the Baker StediVOLT

®

blower motor speed control. This compensates for normal variations

in incoming line voltage.

The cabinet may be provided with an optional UV lamp. The UV lamp and Fluorescent lamp are interlocked to
prevent simultaneous operation.

The cabinet may be provided with an optional 24V DC power supply for low voltage options.

«
...
8
9
10
11
12
...
»

Содержание SterilGARD III Advance


































































Отзывы:

Нет отзывов

Похожие инструкции для SterilGARD III Advance

Бренд: JB Systems Страницы: 7

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Бренд: 3A HEALTH CARE Страницы: 16

Short/cut 2000 Audio Editor

Бренд: 360 Systems Страницы: 4

Бренд: Raytheon Страницы: 68

Бренд: KegLand Страницы: 23

Бренд: laerdal Страницы: 8

Бренд: LAHTI PRO Страницы: 16

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 8

Бренд: Nellcor Страницы: 161

OXIMAX N-600X Series

Бренд: Nellcor Страницы: 210

Бренд: Oase Страницы: 120

Бренд: OAKWORKS Страницы: 24

Бренд: Pahlen Страницы: 20

Бренд: Paia Страницы: 7

Бренд: Yamaha Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды