Baker Hughes Mooney FlowMax HP Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

background image

6 | Baker Hughes

Copyright 2021 Baker Hughes Company. All rights reserved.

Piping Schematics (cont’d)

1. Single Regulator/Single Pilot (Pressure Reducing Regulator)

1. Pilot supply tubing from filter OUTLET connection to the Series 22 pilot INLET port.
2. Type 30 filter mounted in inlet piping.
3. LOADING port of Series 22 pilot connected to Loading connection on the actuator housing of the FlowMax HP regulator
4. Sense line connecting the SENSE Port on the Series 22 pilot to the sense port on the FlowMax HP actuator.
5. Sense line connecting the FlowMax HP regulator to the downstream piping. (Refer to Table 4 on Page 5 for sense piping

recommendations)

6. Series 22 pilot with pilot cartridge in PRV mode.

«
...
6
7
8
9
10
...
»

Содержание Mooney FlowMax HP

























Отзывы:

Нет отзывов

Похожие инструкции для Mooney FlowMax HP

Бренд: eclisse Страницы: 40

Бренд: H3C Страницы: 5

Бренд: H3C Страницы: 27

Бренд: H3C Страницы: 4

Бренд: H3C Страницы: 54

Бренд: H3C Страницы: 10

Бренд: H3C Страницы: 10

Бренд: Febco Страницы: 12

Бренд: HANYOUNG NUX Страницы: 74

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 2

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 36

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

Бренд: Radware Страницы: 98

Бренд: RabbitCore Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды