Baker Hughes Druck Sensycal DPI800, Инструкция по эксплуатации

Страница: 8 / 120

Copyright 2003 Baker Hughes Company.
4 | DPI800/802 Instruction Manual–English
Table 3 shows all the one and two function operations that
are available. If you attach a UMM, you can only use the
options that include IDOS.
1.7 Set up the Settings
When the task is set up (Table 2 & Table 3), use the
Settings menu to adjust the measurement operation.
If there is additional data for a menu option, select Settings
(

) to see the values that are set up. If necessary, adjust
the values. Refer to “Edit Functions” on page 4.
1.8 Edit Functions
Example 1) Set up a label for x:y Scaling = %
IDOS UMM only. An IDOS measurement task.
Pressure options only. A leak test.
To set up the way the instrument works.
Additional data: Refer to: Set Up (Table
1).
a. Optional item
Table 3: Permitted 1 and 2 Function Operations
Function
P1 P2
∆P…
(Table 2) IDOS
(1) (1) (1) (1)
mA
a
a. DPI802/802P only.
(1) (2) (2) (2) (2)
mA(24V)
a
(1) (2) (2) (2) (2)
a
x (2) (2) (2) (2)
x (2) (2) x (2)
IDOS (1) (2) (2) x x
P2
(1) (2) x x (2)
Display: Task
P1 + mA
1
Settings selection
(If applicable)
2 3



Sk2 = Settings
Menu:
Settings
4 5 6
Settings
x:y



(Table 4) [

]/[ ] Sk1 = Edit
Table 2: Menu Options - Select Task
Options
(If applicable) Description
Sk2
55mA
0.000
0.000
P1... g
mA
P1
MENU
OK
Sk2
MENU
OK
Sk1
=
=
123ABC
mA
+04.000
+20.000 +04.000
+20.000
Table 4: Menu Options - Settings
Options
(If applicable) Description
… Units
To select one of the fixed units of measurement
(psi, mbar …).
Gage sensors or sensors with differential
operation (P1, P2, IDOS). A zero correction that
makes the instrument read zero at local
pressure.
To include maximum, minimum and average
values for the measurement task.
To select and set up a tare value for the
measurement task (a specified value or the
reading on the display).
The instrument subtracts a positive tare value,
and adds a negative tare value.
Additional data: Select Settings (

)
To select and set up a scale of values: One local
scale for each measurement task (Maximum: 5).
Additional data (Example 1/2): Select Settings
(

)
To select and set up the filter values to give a
smoother output for the measurement task:
Band as a % of full scale (FS). The filter
compares each new value with the previous
value. If the new value is outside the band, it is
not filtered.
Low pass filter time constant in seconds.
Increase the value to increase the damping
factor.
Additional data: Select Settings (

)
To select and set up the alarm values for the
measurement task (maximum and minimum).
Additional data: Select Settings (

)
Leak Test only. To set an applicable period for
the leak test (Hours:Minutes:Seconds).
Settings
x:y
1 Edit 2 Edit 3
 


+

Sk1 = Edit
Figure A3 - item
[26]
Edit … Edit 4 5
%_


+

Figure A3 - item [26]
Sk1
=
=
123ABC
mA
+04.000
+20.000
+04.000
+20.000
OK Shift BS
_
2 3 4 5 6 7 8 9 0
Q W E R T Y U I O P
A S D F G H J K L
Z X V B N M C
1
Shift
MENU
OK
OK Shift BS
_
_ + . % ^ & * / \
q w e r t y u i o p
a s d f g h j k l
z x v b n m c
-
OK
MENU
OK