background image

12

Service  Support  -  M/C

Service Station Manual

Fuel Saving Tips

A well-maintained vehicle and good driving can contribute a lot to the saving of petrol. Following are a few simple fuel 

saving tips.

•  Avoid harsh braking.

•   Change the gear judiciously according to the speed requirement.

•  Don’t overload the vehicle above the specified payload.

•   Use the accelerator judiciously.

•  Cut off the engine if you want to stop for more than two minutes.

Information on Bike handling :

“Cranking ON and OFF duration” control:

• During Engine crank cycle cranking is allowed only for fixed duration and in between successive cranks (in case engine 

does not start) here is a cooling off period.

Cranking ON-OFF duration control feature to avoid battery discharge -

     - 1st Crank ON (5 sec) & Disable for 2 sec.

     - 2nd Crank ON (5 sec) & Disable for 2 sec.

     - 3rd Crank ON (5 sec) & Disable for 10 sec. After a gap of 10 sec cranking cycle continues.

Recommended speeds for down shifting

From 5

th

to 4

th

Gear

45 Km / h

From 4

th

to 3

rd

Gear

35 Km / h

From 3

rd

to 2

nd

Gear

25 Km / h

From 2

nd

to 1

st

Gear

15 Km / h

Warning : 

•  When shifting down to lower gears, do not shift at such high speed that engine rpm jumps excessively. This may cause 

engine damage & rear wheel may skid. Downshifting should be done at recommended speed as shown in table above. 

•  Always ensure side stand is up while starting. Starter will be disabled if side stand down. With side stand down 

condition & vehicle in gear, engine cranking is disable through ECU & side stand down indication will be displayed in 

speedometer.

INFORMATION FOR CUSTOMER

Содержание pulsar F250 2022

















































Отзывы: