BainUltra AMMA BALNEO Скачать руководство пользователя страница 63

Страница: 63 / 63

AROMACLOUD

DRILLING TEMPLATES

www.bainultra.com

Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.

DRILLING TEMPLATES |

OWNER’S MANUAL

5.562

”

[14.1 cm]

2.062”

[5.2 cm]

6,062”

[15.4 cm]

2.625”

[6.6 cm]

Hole Contour

AromaCloud

Contour

UD HOLE DR

When choosing the position of

AromaCloud on the bath, consider

the following points:

• The Bainultra recommended

position

• The position of controls
• The position of faucets
• The position of tiling flange

if present

• The desired direction with respect

to the bath and the room entrance

Notes:

- AromaCloud must be installed

on bath decking.

- After drilling, verify that there

is a 1/16 inch gap between the

hole and the AromaCloud housing.

• Choose a position for Aroma-

Cloud on the bath.

• Place the adhesive masking

paper over the area of the bath

where AromaCloud will be

installed, to protect the acrylic.

• Drill the 4 holes on the tem-

plate, using a ¼ inch drill bit.

• Complete the rectangular

cutout using a jigsaw equipped

with a fine-tooth metal blade.

Note : Non-factory installation

requires special care (read

the warranty carefully).

RECOMMENDED STEPS

IMPORTANT

Drawing is to scale.

DRAWING OF AROMACLOUD HOLE

Содержание AMMA BALNEO
































































Результаты поиска

Содержание AMMA BALNEO

Отзывы:

BainUltra AMMA BALNEO, Руководство пользователя, Страница: 63 / 63

Результаты поиска

Содержание AMMA BALNEO

Отзывы: