BainUltra AMMA BALNEO Скачать руководство пользователя страница 49

Страница: 49 / 63

AromaCloud

Water Level

Sticker on the Exterior Side.

www.bainultra.com

Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.

AROMACLOUD

OWNER’S MANUAL

AROMACLOUD

INSTALLATION

LOCATION

If performing a home installation of AromaCloud

instead of a BainUltra factory installation, con-

sider the following points when selecting the

installation position:

• AromaCloud must be installed on bath decking;

no other position is acceptable.

• The location recommended by BainUltra.

• The position of the controls, if applicable.

• The position of faucets.

• The position of tiling flange and bath skirt if

present.

• The desired direction with respect to the bath

and the room entrance.

• The possibility that the tub support structure

will require an additional cutout to house Aro-

maCloud.

Note that factory installation by BainUltra will

always be performed for freestanding baths

whose decking has been modified to house

AromaCloud.

Jigsaw with finishing blade.

2 Drill.

1/4 in Bit.

Adhesive masking tape.

INSTALLING THE AROMACLOUD

DRILLING

Refer to the drilling template on page 63 for the

location and diameter of the hole.

After drilling, verify that there is a 1/16 inch gap

between the hole and the AromaCloud housing.

REQUIRED TOOLS

Push wiring through drilled hole.

Connect the AromaCloud to the

transformer underneath the bath.

Remove protective film from watertight

seal.

Fix on the bath deck.

Содержание AMMA BALNEO
































































Результаты поиска

Содержание AMMA BALNEO

Отзывы:

BainUltra AMMA BALNEO, Руководство пользователя, Страница: 49 / 63

Результаты поиска

Содержание AMMA BALNEO

Отзывы: