Bailey Infi 90 IMDSO15 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 48

background image

MAINTENANCE

PREVENTIVE MAINTENANCE PROCEDURES

6 - 4

WBPEEUI240754A0

®

Checking Connections

NOTE: Power to the cabinet should be off while performing this pre-
ventive maintenance task.

Check all signal wiring, power and ground connections within
the cabinet to verify their integrity. When checking connec-
tions, always turn a screw, nut or other fastening device in the
direction to tighten only. If the connection is loose, it will be
tightened. If the connection is tight, the tightening action will
verify that it is secure. There must not be any motion done to
loosen the connection.

1. Verify that all power connections within the cabinet are
secure.

2. Verify that all wiring connections to the termination unit,
or termination module are secure.

WARNING

There are exposed AC and DC connections inside the cabinet.
These exposed electrical connections present a shock hazard
that can cause injury or death.

If input or output circuits are a shock hazard after disconnect-
ing system power at the power entry panel, then the door of the
cabinet containing these externally powered circuits must be
marked with a warning stating that multiple power sources
exist.

«
...
35
36
37
38
39
...
»

Содержание Infi 90 IMDSO15

















































Отзывы:

Нет отзывов

Похожие инструкции для Infi 90 IMDSO15

Бренд: Gantner Страницы: 56

Бренд: Sole Diesel Страницы: 8

Бренд: Oceanic Страницы: 11

Бренд: Vacon Страницы: 6

Бренд: Vacon Страницы: 24

Бренд: Vacon Страницы: 30

Бренд: Vacon Страницы: 81

Бренд: Vacon Страницы: 100

Бренд: Bartlett Страницы: 7

Бренд: WABCO Страницы: 4

Бренд: Rayrun Страницы: 4

Бренд: Parker Страницы: 29

HydroTap G5 Touch-Free Wave

Бренд: Zip Страницы: 24

Pearldex Series

Бренд: KaMo Страницы: 2

Бренд: M-system Страницы: 7

Бренд: Adaptec Страницы: 2

Бренд: Webasto Страницы: 12

EAGLE CORE PLUS

Бренд: PrimaLuceLab Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды